(1) The Delhi Standards of Weights and Measures (Enforcement) Rules, 1988 shall cease to have effect from the date of issue of these rules.
(2) Notwithstanding any such repeal, anything done or any action taken or purported to have been taken or any licence granted under the rules repealed by sub-rule (1), shall in so far as these are not inconsistent with these rules or the Legal Metrology Act, 2009 (1 of 2010), be deemed to have been done, taken or granted under the corresponding provisions of these rules.
SCHEDULE – I (See rule 10) Exceptions referred to in Rule 10 1- The following commodities may be sold by weight, measure or number as show against the commodity.
TABLE --------------------------------------------------------------------------------------------------------------------- Sr. No. Commodity Whether declaration to be expressed in terms of weight, measure or number or two or more of them.
(1) (2) (3) -------------------------------------------------------------------------------------------------------------------- 1- Aerosol products weight 2- Acids in liquid form weight or Volume 3- Compressed or liquified weight and equivalent volume at stated temperature Gas (but not liquified and pressure Petroleum gas) 4- Butter (incl. peanut butter), weight Cheese, curd, ghee 5- Electric cables length or weight 6- Electric wire length or weight 7- Fencing wire length or weight 8- Hair oil, un-perfumed weight or volume 9- Fruits and vegetables number or weight 10- Furnace oil weight or volume 11- Linseed oil and other weight or volume vegetable oils 12- Heavy residual fuel oil weight 13- Industrial diesel fuel volume 14- Honey, malt extract, golden weight syrup treacle 15- Ice cream and other similar weight or volume frozen products 16- Liquid chemicals weight or volume 17- Liquid petroleum gas weight 18- Nails, wood screws number or weight 19- Paint (other than paste paints volume or solid paints), varnish and varnish stairs, enamels 20- Papad number and weight 21- Paste paint, solid paint weight 22- Ressogulla, Gulabjamun weight and other sweet preparations 23- Ready made garments number and size 24- Sauce, all kinds weight 25- Tyres and tubes number 26- Yarn Weight or length of yarn ---------------------------------------------------------------------------------------------------------------------
SCHEDULE – II–A [See rule 11 (1)] Form – LM – 1 [Application form for licence as Manufacturer of weights & measures under the Legal Metrology Act, 2009] To, To be filled by the Comments of the Applicant inspection officer
(1) (2) (3)
1. Name of the manufacturing concern for which licence ..........................................
is desired.
2. Complete address of the concern. Whether premises ............................................
are owned/rented/taken on lease/leave licence, duly supported by documents.
3. Date of Establishment of workshop/factory. .......................................
4. Name (s) and address (s) along with their father's/ ..........................................
husband's name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company
5. The date and current registration number of factory/ ....................................
shop/ establishment/ Municipal Trade licence.
6. Nature of manufacturing activities at present. ..........................................
7. The type of weights and measures proposed to be .........................................
manufactured viz :
(i) Weights
(ii) Measures
(iii) Weighing Instruments
(iv) Measuring Instruments with details in each case.
8. The number of persons employed/proposed to be employed ........................... (i) Skilled
(ii) Semi-skilled
(iii) Unskilled
(iv) Specialist trained in the line
9. The monogram or trade mark intended to be imprinted .......................................
on weights and measures to be manufactured.
10. Details of machinery, tools accessories, owned and ...........................................
used for manufacturing weights measures etc.
11. Details of foundry/workshop facilities arranged. ..........................................
Whether ownership, long term lease etc.
12. Facilities of steel casting and hardness testing of .......................................
Vital parts etc or other means.
13. Availability of electric energy. ...........................................
14. Details of loan received from Government or financial ..............................................
Institution. If so, give details.
15. Name of bankers, if any. ............................................
16. VAT/ Sales Tax Registration Number/CST Number/ ........................................
Professional Tax registration Number/IT Number.
17. Have you applied previously for a manufacturer's ..............................................
licence? If so, when and with what results?
18. (a) Whether the item (s) proposed to be .....................................
manufactured will be sold within the State or out side the state or both.
(b) Details of Model Approval received from Government of India;
(c) When can you produce for inspection samples of your products for which licence is desired ?
To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We agree to deposit the Scheduled licence fees with Government as soon as required to do so by the Licensing Authority.
All the information furnished above is true to the best of my/our knowledge.
Place : ...................................
Date : Signature and Designation To be filled in by Departmental Officer of the Government of National Capital Territory of Delhi Date of Receipt of Application:
Serial Number of application:
Date of inspection:
Recommendation of Inspecting Officer:
Place: ..................................
Date: Signature and Designation of Inspecting Officer Final orders of Licensing Authority Licence granted / refused:
Licence Number:
Valid till:
Place:
Date:
Signature and Designation
SCHEDULE – II-A [See rule 11 (1)] Form LR – 1 [Application for licence as Repairer of Weights & Measures under the Legal Metrology Act, 2009] To, To be filled by Comments of the the applicants inspecting officer 1 2 3
1. Name of the concern seeking the licence. ..................................
2. Complete address of the workshop. ..................................
3. (a) Whether premises are owned/rented/taken. on ..................................
lease dully supported by documents.
(b) Date of establishment.
4. Name (s) and address (s) along with their father's/ ..................................
husband's name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company.
5. Number and date of shop/establishment/current ..................................
Municipal Trade Licence.
6. Professional Tax/IT Tax registration Number etc if any. ..................................
7. The type of weights and measures proposed to repaired. ..................................
8. Area in which you wish to operate. ..................................
9. Previous experience in the line. ..................................
10. Number of skilled staff employed or proposed to be ..................................
employed:
(i) Skilled
(ii) Semi-skilled
(iii) Unskilled
(iv) Employees trained in the line
11. Details of machinery/tools/accessories available. ..................................
12. Availability of electric energy. ..................................
13. Have you sufficient stock of loan/test weights. etc.? ..................................
Give details.
14. Have you applied previously for a repairer's licence? ..................................
If so, When and with what results?
To be certified by the applicant(s) Certified that I/We have read the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We agree to deposit the Scheduled licence fees with Government as soon as required to do so by the Licensing Authority.
All the information furnished above is true to the best of my/our knowledge.
Place: ...................................
Date: Signature and Designation To be filled in by Departmental Officer of the Government of National Capital Territory of Delhi Date of Receipt of Application:
Serial Number of Application:
Date of Inspection :
Recommendation of Inspecting Officer:
Place: ...................................
Date: Signature and Designation of Inspecting Officer Final orders of Licensing Authority Licence granted/refused:
Licence Number:
Valid till:
Place:
Date:
Signature and Designation
SCHEDULE – II–A [See rule 11 (1)] Form LD-1 [Application Form for Licence as Dealers in Weights & Measures under the Legal Metrology Act, 2009] To, To be filled by Comments of the the applicant inspecting officer 1 2 3
1. Name of the establishment/shop/person seeking the ..................................
licence.
2. Complete address of the establishment etc. …………………………
3. Date of establishment. ..................................
4. Name (s) and address (s) of proprietors and / or partners ............................
and Managing Director (s) in the case of Limited company.
5. Number and date of Registration Number of current ..................................
shop/establishment/Municipal Trade licence.
6. Categories of weights and measures sold/proposed ..................................
to be sold at present.
7. Registration Number of VAT/CST/Sales Tax/Professional ..................................
Tax/Income Tax.
8. Do you intend to import weights, etc. from places ..................................
outside the State/Country ? If so indicate sources of supply. (Give details of manufacturer's trade mark/ monogram and his licence number) and provide
(a) Registration of Importer of Weights and Measures, if any
(b) Approval of model imported into India by Central Government.
9. Have you applied previously for a dealer's licence, ..................................
either in this State or elsewhere ? If so give details?
To be certified by the applicant(s) Certified that I/We have read the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We agree to deposit the Scheduled licence fees with Government as soon as required to do so by the Licensing Authority.
All the information furnished above is true to the best of my/our knowledge.
Place: ...................................
Date: Signature and Designation To be filled in by Departmental Officer of the Government of National Capital Territory of Delhi Date of Receipt of Application:
Serial Number of Application:
Date of Inspection:
Recommendation of Inspecting Officer:
Place: ...................................
Date: Signature and Designation of Inspecting Officer Final orders of Licensing Authority Licence granted/refused:
Licence Number:
Valid till:
Place:
Date:
Signature and Designation
SCHEDULE― II―B [See rule 11 (2)] Form LM-2 [Application for renewal Licence as Manufacturer of Weights & Measures under the Legal Metrology Act, 2009] To, To be filled by Comments of the the applicants inspecting officer 1 2 3
1. Name and complete address of the manufacturing ..................................
concern for which renewal of licence is desired.
2. Manufacturing Licence No. ..................................
3. Name (s) and address (s) along with their father's/ ..................................
husband's name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company.
4. (a) Type of weights and measures which are ..................................
manufactured as per licence granted.
(b) Do you propose any change. ..................................
5. The monogram or trade marks used on weights and ..................................
measures manufactured by you.
6. Details of workshop facilities available. ..................................
7. Details of production and sales in the last 5 years. ..................................
8. Number and date of shop/establishment Registration ..................................
Number.
9. Registration Number of VAT/Sales Tax/CST/Professional ..................................
Tax/Income Tax.
To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We have deposited the Scheduled licence fees of Rs. ........................... (Rupees .......................................) to the Sub-Treasury/Bank on ...................................................... and the original Challan is enclosed.
All the information furnished above is true to the best of my/our knowledge.
Place: ...................................
Date:
Signature and Designation
SCHEDULE ―II―B [See rule 11 (2)] Form LR-2 [Application for renewal Licence as Repairer of Weights & Measures under the Legal Metrology Act 2009] To, To be filled by Comments of the the applicants inspecting officer 1 2 3
1. Name and complete address of the repairing concern/ ..................................
person seeking renewal of the licence .
2. Repairer's Licence Number. ..................................
3. Name (s) and address (s) along with their father's/ ..................................
husband's name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company.
4. Registration Number and date of current shop/ ..................................
establishment/Municipal Trade Licence.
5. Registration Number of VAT/ Sales Tax/CST/Professional ..................................
Tax/Income Tax.
6. (a) The Type of weights and measures repaired ..................................
as per licence granted.
(b) Do you propose any change. ..................................
7. Area in which you are operating. ..................................
8. Have you sufficient stock of loan/test weights, etc.? ..................................
9. Please give details with particulars of stamping. ..................................
To be certified by the applicant (s) Certified that I/ We have read the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We have deposited the Scheduled licence fees of Rs. ........................... (Rupees .......................................) to the Sub-Treasury/ Bank on ...................................................... and the original Challan is enclosed.
All the information furnished above is true to the best of my/our knowledge.
Place: ...................................
Date:
Signature and Designation
SCHEDULE― II―B [See rule 11 (2)] Form LD-2 [Application for renewal Licence as Dealer in Weights & Measures under the Legal Metrology Act 2009] To, To be filled by Comments of the the applicants inspecting officer 1 2 3
1. Name of the establishment/shop/person seeking the ..................................
renewal of licence .
2. Dealer's Licence Number. ..................................
3. Date of establishment. ..................................
4. Name (s) and address (s) along with their father's/ .................................. husband's name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company.
5. Registration Number and date of shop/establishment/ .................................. current Municipal Trade Licence.
6. Categories of weights and measures sold at present. .................................. .
7. Registration Number of VAT/ CST/Sales Tax/Professional ..................................
Tax/Income Tax.
8. Are you intending to import weights and measures etc. .................................. from places outside the State/Country? If so, indicate sources of supply from the State (s)/Country (s).
(Give details of manufacturer's trade mark/ monogram and his licence number.)
To be certified by the applicant (s) Certified that I/We have the Legal Metrology Act, 2009 and the Delhi Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under.
I/We have deposited the Scheduled licence fees of Rs. ........................... (Rupees .......................................) to the Sub-Treasury/Bank on ...................................................... and the original Challan is enclosed.
All the information furnished above is true to the best of my/our knowledge.
Place: ...................................
Date: Signature and Designation.
SCHEDULE―III [See rule 11 (3)] Licensing Forms FORM LM-3 Government of National Capital Territory of Delhi OFFICE OF THE CONTROLLER OF LEGAL METROLOGY Licence to Manufacture, weights, measures, weighing or measuring instruments.
Licence No…………. Year ………………..
1- The Controller of Legal metrology hereby grants to ………………………… (Name and address of party or parties) a licence to manufacture the following:- (Include details of the weights, measures, weighting instruments or measuring instruments that are licenced to be manufactured by the party).
2- The licence is valid for the party named above in respect of his workshop located at …………….
3- This licence is valid from ……………… to ……………..
4- The manufacturer shall comply with the conditions noted below. If he fails to comply with anyone of these, his licence is liable to be cancelled.
5- The trade mark monogram being used by the manufacturer is as under.
…………………… (Signature) Controller of legal Metrology (Seal) Government of National Capital Territory of Delhi Date ………………..
Place ………………..
Note: In the case of firm, its name with the names of all names of all persons having interest in the business should be given in paragraph 1.
CONDITIONS OF LICENCE
1. The person in whose favour this licence is issued shall. -
(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;
(b) Not encourage or countenance any infringement of the provisions of the Act. or the Rules amended from time to time;
(c) Exhibit this licence in some conspicuous part of the premises to which it relates;
(d) Comply with any general or special directions that may be given by the Controller of legal metrology;
(e) Surrender the licence in the event of closure of business and/ or cancellation of Licence;
(f) Present the weights, measures, weighing or measuring instruments as the case may be manufactured and meant for use within the State, to the legal metrology officer for verification and stamping before sale;
(g) Submit the application for renewal of this licence as required under the rules within thirty days of expiry of the validity of the licence.
2. Every condition prescribed after the issue of this licence shall if notified in the Official Gazette, be binding on the persons to whom the licence has been granted.
Renewal Entries Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Seal Seal Seal Seal Seal Seal
SCHEDULE― III [See rule 11 (3)] Licencing Forms FORM LR-3 GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI OFFICE OF THE CONTROLLER OF LEGAL METROLOGY LICENCE TO REPAIR WEIGHTS, MEASURES, WEIGHING INSTRUMENTS OR MEASURING INSTRUMENTS Licence No ………. Year ……… 1- The Controller of legal metrology hereby grants to …………………………… (Name and address of Party or Parties) a licence to repair the following:- (Include details of the types of weights, measures, weighing instruments or measuring instruments that are licenced to be repaired by the party) 2- The licence is valid for the party named above in respect of his workshop located at …………….
3- This licence is valid from ……………….. to ….. …………… 4- The repairer shall comply with the conditions noted below. If he fails to comply with any one, his licence is liable to be cancelled.
5- The party is licenced to repair weights, measures, weighting and measuring instruments in the areas mentioned below – (Signature) Controller of Legal Metrology (Seal) Government of National Capital Territory of Delhi Date…………………….
Place………………..….
Note: In the case of firm, its name with the names of all persons having any interest in the business should be given in paragraph (1).
Conditions of Licence
1. The person in whose favour this licence is issued shall. -
(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;
(b) Not encourage or countenance any infringement of the provisions of the Act or the Rules for the time being in force;
(c) Exhibit this licence in some conspicuous part of the premises to which it relates;
(d) Comply with any general or special directions that may be given by the Controller of legal metrology;
(e) Surrender the licence in the event of closure of business and/or cancellation of Licence;
(f) (i) Present the weights, measures, weighing or measuring instruments as the case may be duly repaired to the legal metrology officer for under taking verification and stamping as specified in rule 14(1), before delivery to the user.
(ii) In the case of weights, measures weighing or measuring instruments, if they are serviced/repaired before the date on which the verification falls due and where, in the process and the verification stamp of the legal metrology officer is defaced, removed or broken, they shall be presented duly repaired to the legal metrology officer for re-verification and stamping before delivery to the user.
(g) Submit the application for renewal of this licence as required under the rules within thirty days of expiry of the validity of the licence.
2. Every condition prescribed after the issue of this licence shall, if notified in the Official Gazette, be binding on the persons to whom the licence has been granted."
Renewal Entries Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Seal Seal Seal Seal
SCHEDULE― III [See rule 11 (3)] Licencing Form FORM – LD- 3 GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI Office of the Controller of legal metrology Licence to a dealer in weights, measures, weighing instruments or measuring instruments Licence No. …….. Year …………..
1- The Controller of legal metrology hereby grants to …………………………… (Name and address of party or parties) a licence to deal in the following (Indicate details of the types weights and measures, weights, or measuring instruments that are licenced to be dealt with by party) 2- The licence is valid for the party named above in respect of his premises located at 3- This licence is valid form ……………. To. …………….
4- The dealer shall comply with the conditions noted below. If he fails to comply with any one of those his licence is liable to be cancelled.
(Seal) (Signature) Controller of Legal Metrology Government of National Capital Territory of Delhi Date…………….
Place……………….
Note: In the case of firm its name with the names of all persons having any interest in the business should be given in paragraph (1).
CONDITIONS OF LICENCE
1. The person in whose favour this licence is issued shall. -
(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;
(b) Not encourage or countenance any infringement of the provisions of the Act or the Rules for the time being in force;
(c) Exhibit this licence in some conspicuous part of the premises to which it relates;
(d) Comply with any general or special directions that may be given by the Controller of legal metrology;
(e) Surrender the licence in the event of closure of business and/or cancellation of Licence;
(f) Submit the application for renewal of this licence as required under the rules within thirty days of expiry of the validity of the licence.
(g) Not sell or offer, expose or possess for sale any non-standard weight or measure.
2. Every condition prescribed after the issue of this licence shall, if notified in the Official Gazette, be binding on the persons to whom the licence has been granted.
Renewal Entries Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Current No…………….. Date ……….
Renewed for Controller of Legal Metrology Seal Seal Seal Seal Seal Seal
SCHEDULE – IV [See rule – 11 (4) & (5)] GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI Office of Controller of Legal Metrology Licencing and renewal fees for manufacturers, repairers of dealers of weights and measures
1. Issue of licence / renewal of licence to:
(i) Manufacturers Rs. 500/- per year (five hundred rupees per year)
(ii) Repairers Rs. 100/- per year (one hundred rupees per year)
(iii) Dealers Rs. 100/- per year (one hundred rupees per year)
2. Alteration of licence: Rs. 50/-(fifty rupees)
3. Issue of duplicate licence: Rs. 10/- (ten rupees)
SCHEDULE–V [See rule 11 (6)] GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI Office of Controller of Legal Metrology Register of licenced Manufacturers/ Repairers/ Dealers of weights, measures, weighing / measuring instruments Office of ………………….
Lice nce Num ber Date of issue / rene wal Name and complet e address of the manufac turer /repairer / dealer Place where works hop/ factor y is situate d Articles to be manufact ured/ repaired/ sold Trade mark/ monog ram being used Orders regardi ng cancell ation of licence Res ult of app eal Signat ure of compe tent authori ty Re m Ar k 1 2 3 4 5 6 7 8 9 10 Note: Column (4) does not apply to dealers; column (6) does not apply to repairers and dealers.
SCHEDULE ―VI [See rule 11(8)] GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI Office of Controller of Legal Metrology Security deposit to be made by licensee repairer:
Repairer of weights and measures including weighing and measuring instruments. Rs. 200.00 (Two hundred rupees) \
SCHEDULE – VII [See rule 13] Register to be maintained by the Manufacturers of weights and measurers.
1- Name and address of the manufacturer ………………………………………...
2- Description of the weight or measure ………………………………………….
3- (i) No. of the manufacturing licence ……………………………………………
(ii) Date on which the licence was issued ………………………………………
(iii) Period of validity of the licence ………………………………………..
4- Particulars of order, if any, suspending or revoking ………………………… the licence.
Sold within the state S.No. Month Unsold stock from previous month Quantity manufactured during the month Total 3+4 No. of item sold Dispatch voucher no. and date 1 2 3 4 5 6 7 Sold outside the state Name of the state No. of items sold Dispatch voucher no. and date Total sold (6+9) Balance (5-11) Remarks 8 9 10 11 12 13 Schedule – VII [See rule 13] Form LR-4 Register to be maintained by the Repairer in respect of weights and Measures Name and address of the repairer ……………….. Licence No……………….
Date of Licensing ………………..
S. No. Date Name of the user from whom received Items and their Nos.
booked for repair Receipt No. and date of issue to the user 1 2 3 4 5 Amount of repairing charges Amount of verification fee Total amount charged Date of return to the user Remarks 6 7 8 9 10 Schedule – VII [See rule 13] LD-4 Register to be maintained by dealer in weights and measures.
1- Name and address of the dealer ………………………………………………...
2- Description of the weight or measure …………………………………………..
3- (i) Dealer licence No. …………………………………………………………...
(ii) Date on which the licence was issued ………………………………………
(iii) Period of validity of licence ……………………………………………….
4- Particulars of order, if any suspending or Revoking the licence. ………………………………………………..
5- Category of weight or measure ………………………………………………...
(Category A or B) Sr.
No.
Month Unsold stock from the previous month Brought from within the state during the month Brought from outside the state during the month Total (3+4+5) 1 2 3 4 5 6 Sold within the state Sold outside the state No. of items sold Dispatch voucher no. and date No. of items sold Dispatch voucher No. and date Name of the state Total sold (7+9) Balance (6-12) Remarks 7 8 9 10 11 12 13 14 Schedule – VIII [See rule 15 (3)] GOVERNMENT OF NATIONAL CAPITAL TERRITORY OF DELHI Office of the Controller, legal metrology, Certificate of verification Name of Legal metrology officer …………………………………….……… No…………………..
I hereby certify that I have this day verified and stamped / rejected the under mentioned weights, measurers, etc.
Belonging to …………………………………. Locality ……………………………… Denomination Weighing instruments Quanti ty Weigh ts Measur es Capaci ty Clas s Manufactu rer Typ e Measurin g instrume nts Verificati on Fee Rs. p Carriage, conveyan ce adjusting charges etc.
1 2 3 4 5 6 7 8 9 10 Total Rs. …….. deposited vide T. Receipt/ Money receipt .No. …… dated ....……… Repaired by/ Used by ………………………. (Signature) Next verification due on …………….. Legal metrology officer Note:- In the case of rejected weights, measures, etc the legal metrology officer shall give separate Certificate of rejection mentioning the reasons of rejection against each item.
Schedule-IX [See Rule 16] Fee payable for verification and Stamping of Weights and Measures and Weighing and Measuring Instruments 1- (a) Bullion Weights:
Denomination
(1) Fee per piece (Rs.)
(2) 10 Kg. 30.00 5 Kg. 20.00 2 Kg. 20.00 1 Kg. 20.00 500 g. 15.00 200 g. 15.00 100 g. 15.00 50 g. 15.00 20 g. 15.00 10 g. 15.00 5 g. 15.00 2 g. 15.00 1g 15.00
(b) Carat Weights:
100g (500 c) 20.00 40g (200 c) 20.00 20g (100 c) 20.00 10g (50 c) 20.00 4g (20 c) 20.00 2g (10 c) 20.00 1g (5 c) 20.00 400mg (2 c) 20.00 200mg (1 c) 20.00 100mg (0.5 c) 20.00 40mg (0.02 c) 20.00 20mg (0.01 c) 20.00 10mg (0.05 c) 20.00 4mg (0.02c) 20.00 2mg (0.01 c) 20.00 1mg (0.005c) 20.00
(c) Cylindrical knob type weights:
Denomination
(1) Fee per piece (Rs.)
(2) 10 Kg. 20.00 5 Kg. 20.00 2 Kg. 15.00 1 Kg. 10.00 500 g. 5.00 200 g. 5.00 100 g. 5.00 50 g. 5.00 20 g. 5.00 10 g. 5.00 5 g. 5.00 2 g. 5.00 1g 5.00
(d) Sheet metal Weight (other than Bullion) Denomination
(1) Fee per piece (Rs.)
(2) 500 mg. 5.00 200 mg. 5.00 100 mg. 5.00 50 mg. 5.00 20 mg. 5.00 10 mg. 5.00 5 mg. 5.00 2 mg. 5.00 1 mg. 5.00
(e) Iron hexagonal, knob type weights and parallelepiped weights:
Denomination
(1) Fee per piece (Rs.)
(2) 50 Kg. 25.00 20 Kg. 20.00 10 Kg. 20.00 5 Kg. 20.00 2 Kg. 15.00 1 Kg. 10.00 500 g. 5.00 200 g. 5.00 100 g. 5.00 50 g. 5.00 20g 5.00 10g 5.00 5g 5.00 2g 5.00 1g 5.00
(f) Standard weights for testing of high capacity weighing machines:
Denominations Fee corresponding to Max permissible relative error
0.5/10000 in Rs.
Fee corresponding to Max permissible relative error
3.3/10000, 1.7/10000 and
1.0/10000 in Rs.
100kg 75.00 50.00 200kg 150.00 100.00 500kg 300.00 200.00 1000kg 750.00 500.00 2000kg 1500.00 1000.00 5000kg 3000.00 2000.00 2- Capacity Measures:
Denomination
(1) Fee per piece (Rs.)
(2) 100 litre and above Rs. 50 for the Ist 100 litre plus Rs. 7 for every additional 100 litre or part thereof subject to maximum of Rs. 5000.
50 l 50.00 20 l 20.00 10 l 20.00 5 l 10.00 2 l 10.00 1 l 10.00 500 ml 10.00 200 ml 10.00 100 ml 10.00 50 ml 10.00 20 ml 10.00 10 ml 10.00 5 ml 10.00 2 ml 10.00 1 ml 10.00 3- Length Measures:
(a) Non-Flexible – Denomination
(1) Fee per piece (Rs.)
(2) 2 m. 10.00 1 m. 10.00
0.5 m. 20.00 1 m. graduated (at every cm) 20.00
0.5 m. graduated (at every cm) 20.00
(b) Fabric Plastic/ Woven/Steel tapes – Accuracy Class
(1) Fee per metre in Rs.
Class-I 1.00 Class-II 0.50 Class-III 0.50
(c) Folding Scales – Denomination
(1) Fee per piece (Rs.)
(2) 1 m. 10.00
0.5 m. 10.00
(d) Surveying Chain – Denomination
(1) Fee per piece (Rs.)
(2) 30 m. 100.00 20 m. 100.00 4- Beam Scale Class A & B:
Denomination
(1) Fee per piece (Rs.)
(2) 200 kg. 400.00 100 kg. 300.00 50 kg. 150.00 20 kg. 150.00 10 kg. 150.00 5 kg. 100.00 2 kg. 100.00 1 kg. 100.00 500 g and below 60.00 5- Beam Scales Class C& D:
Denomination
(1) Fee per piece (Rs.)
(2) 1000 kg. 200.00 500 kg 200.00 300 kg 200.00 200 kg 100.00 100 kg 100.00 50 kg 20.00 20 kg 20.00 10 kg 20.00 5 kg 15.00 2 kg 15.00 1 kg 15.00 500 g and below 10.00 6- Non-Automatic Weighing Instruments - Mechanical (analogue) Class III & IIII :
400 t 4000.00 300 t 3000.00 200t 3000.00 150 t 2000.00 100 t 2000.00 80 t 2000.00 60 t 2000.00 50 t 2000.00 40 t 2000.00 30 t 2000.00 25 t 2000.00 20 t 2000.00 15 t 2000.00 10 t 1000.00 5 t 500.00 3 t 400.00 2 t 400.00 1500 kg 300.00 1000 kg 300.00 500 kg 300.00 300 kg 200.00 250 kg 200.00 200 kg 100.00 150 kg 100.00 100 kg 100.00 50 kg 100.00 30 kg 100.00 25 kg 60.00 20 kg 60.00 15 kg 30.00 10 kg 30.00 5 kg 30.00 3 kg 30.00 2 kg 30.00 1 kg 15.00 500 g. and below 15.00 7- Non-Automatic Weighing Instruments - Electronic Class III & IIII :
400 t 4000.00 300 t 3000.00 200t 3000.00 150 t 2000.00 100 t 2000.00 80 t 2000.00 60 t 2000.00 50 t 2000.00 40 t 2000.00 30 t 2000.00 25 t 2000.00 20 t 2000.00 15 t 2000.00 10 t 1000.00 5 t 1000.00 3 t 500.00 2 t 500.00 1500 kg 250.00 1000 kg 250.00 500 kg 250.00 300 kg 200.00 250 kg 200.00 200 kg 200.00 150 kg 200.00 100 kg 200.00 50 kg 200.00 30 kg 200.00 25 kg 200.00 20 kg 100.00 15 kg 100.00 10 kg 100.00 5 kg 100.00 3 kg 100.00 2 kg 100.00 1 kg 100.00 500 g. and below 100.00 8-Not Automatic Weighing instruments both mechanical and electronics class I & II:
9- Automatic Weighing Instrument:
Capacity Fee in Rs.
Exceeding 100 t 4000.00 Not exceeding 100t but exceeding 50t 3000.00 Not exceeding 50t but exceeding 10t 2000.00 Not exceeding 10t but exceeding 1t 1000.00 Not exceeding 1t but exceeding 50kg 500.00 Not exceeding 50kg but exceeding 10kg 250.00 Not exceeding 10kg 200.00 Capacity Fee (Rs.)
Exceeding 50 t 3000.00 Not exceed 50t but exceed 10t 2000.00 Not exceed 10t but exceed 1t 1000.00 Not exceed 1t but exceed 50kg 500.00 Not exceed 50kg but exceed 10kg 250.00 Not exceed 10kg 200.00 10- Volumetric measuring instruments:
(a) Dispensing pumps each pump : Rs.1000.00 per unit
(b) Totalizing counter : Rs. 500.00 per unit
(c) Other instruments :
.
Capacity Fee in Rs.
Exceeding 100 litre Rs. 500 for the Ist 100 liters plus Rs. 250 for every additional 100 liters or part thereof Not exceeding 100 litre but exceeding 50 litre 500.00 Not exceeding 50 litre but exceeding 20 litre 250.00 Not exceed 20 litre 200.00 11- Flow meters:
Flow rate up to 100 litre/ min. Rs.2000.00 Above 100 litre/ min upto 500 litre/ min Rs.3000.00 Above 500 litre /min. Rs.5000.00 12- Linear Measuring Instruments:
Taxi, Autorishaw meters Rs.100.00 Other meters Rs.50 for the Ist 1000 m. or part there of Plus Rs. 5.00 for every additional 100 m. or part thereof 13- Clinical Thermometer Rs. 0.50 per unit 14- Water meter Rs. 25.00 per unit 15- Peg Measure:
30 ml 50.00 60 ml 50.00 100 ml 50.00
16. CNG Dispensers: Rs. 1000.00 per unit
17. LPG Dispensers: Rs. 1000.00 per unit
18. Counter Machine:
(i) Counter machine up to capacity 10kg: Rs. 20.00
(ii) Counter machine above capacity 10kg: Rs. 50.00
SCHEDULE -X [See rule 24(1)] Form of appeal against an order of a Legal metrology officer/ Controller Legal Metrology:- 1- Name and address of the appellant 2- No. and date of order of Legal metrology officer/ Controller of Legal Metrology against which the appeal is preferred.
3- Whether the appellant desires to be heard in person or through an authorized representative.
4- Grounds of appeal
SCHEDULE –XI [See rule 25] Compounding fees for various offences Sr. No. Section and nature of offence Penal Section Compounding fee 1 S. 8(3) Use of weight, measure or numeration other than the Standard weight, measure or numeration 25 Rs.2500.00 2 S. 8(4) Manufacture of weight or measure not conforming to Standards 27 Rs.2000.00
3. S. 10 Transaction or dealing or contract in respect of goods etc., by weight, measure or number than prescribed.
28 Rs.1000.00
4. S. 11 Quote or make announcement or issue or exhibit of price list or changing of price than in accordance with standard unit of weight or measure or numeration.
29 Rs.1000.00
5. S. 12 Demanding or receiving any articles or thing on service in excess or less than the quantity specified by contract or agreement.
30 Rs.1000.00
6. S. 17 Maintenance of records, registers by manufacturer, dealer or repairer and production of weight, measure document, register on demand 31 Rs.500.00
7. S.18(1) Compliance of declaration in respect of pre-packaged commodity by manufacturer/ dealer 36(1) Rs. 2500.00
8. S. 18(1) Compliance of net quantityrequirement of pre-packaged commodity by manufacturer 36(2) Rs.15000.00
9. S. 23 Manufacturer/ repair/ sale of weight or measure only with licence 45 Rs.5000.00
10. S. 23 Repair/sale of weight or measure only with licence.
46 Rs. 2000.00
11. S. 24 Use of verified weight or measure in transaction or protection 33 Rs. 5000.00
12. S. 33 Sale of weight or measure without verification.
33 Rs. 5000.00
13.
S. 34 Sale or delivery of commodities by non-standards weights or measure 34 Rs. 2500.00
14. S. 35 Rendering service by non-standard weight or measure 35 Rs. 2500.00
15. S. 47 Tampering with licence 47 Rs. 5000.00
16. S. 53(3) Provision of any rule made under the Act 53(3) Rs. 500.00 By order and in the Name of the Lt. Governor of the National Capital Territory of Delhi (DHARAM PAL) Secretary, Legal Metrology (Weights & Measures Department)