(1) If it appears to the Inspector that any site or place at which any building or other construction work is being carried on, is in such condition that it is dangerous to life, safety or health of building workers or the general public, he may in writing, serve on the employer of building workers or on the owner of the establishment or on the person in-charge of such site or place, an order prohibiting any building or other construction work at such site or place until measures have been taken to remove the cause of the danger to his satisfaction.
(2) An Inspector serving an order under sub-rule (1) shall endorse a copy to the Chief Inspector of Inspection of Building and Construction
(3) Such prohibition order shall be complied with by the employer forthwith.
-100-
(4) Any person aggrieved by an order under sub-rule (1) may within 15 days from the date on which the order is communicated to him, prefer an appeal to the Chief Inspector of Inspection of Building and Construction or where such order is by the. Chief Inspector of Inspection of Building and Construction to the Secretary to the Government, Labour & Employment Department and the Chief Inspector of Building and other Construction Work or the Secretary to the Government, Labour & Employment Department, as the case may be shall, after giving the appellant an opportunity of being heard, dispose of the appeal as expeditiously as possible.
Provided that the Chief Inspector of Inspection of Building and Construction or the Secretary to the Government, Labour and Employment Department, as the case may be, may entertain the appeal after the expiry of the said period of 15 days if he is satisfied that the appellant was prevented by sufficient cause from filing the appeal in time.
Provided further that the prohibiting, shall be complied with, pending the decision of the Chief Inspector of Inspection of Building and Construction or the Secretary to Government, Labour and Employment Department.
Schedule-I (See rule 56(a) and 71(a)) Manner of test and examination before taking lifting appliance, lifting gear and wire rope into use for the first time.
Testloads
(1) Lifting appliances:-livery lifting appliance with its accessory gear, shall be subjected to a test toad which shall exceed the safe working load (SWL) as specified in the following table:- TABLE Safe working load Test load Upto 20 tonnes .. 25 per cent in excess of safe working load.
20 to 50 tonnes .. 5 tonnes in excess of safe working load.
Over 50 tonnes .. 0 percent in excess of safe working load.
-101-
(2) Lifting Gear:- (a) Every ring. hook, chain, shackle, swivel, eye-bolt, plate clamp, triangular plate or pulley block (except single sheave block) shall be subjected to a test load which shall not be less than the load as specified in the following table:- TABLE Safe working load (in tonnes) Upto 25 ..
Test load (in tonnes) 2 x safe working load Above 25 .. (1.22 x safe working load)+20
(b) In the case of a single sheave block, the safe working load shall be the maximum load which can safely be lifted by the block when suspended by its head fitting and the load is attached to a rope which passes around the sheave of the block and a test load not less than four times the proposed safe working load shall be applied to the head of the block.
(c) In the case of multi sheave block, the test load shall not be less than the load as specified in the following table:— TABLE Safe working load Test load (in tonnes) (in tonnes) Upto 25 .. 2 x safe working load 25 to 160 .. (0.9933 x safe working load)+27 above 160 .. 1.1 x safe working load.
(d) In the case of hand-operated pulley blocks used with pitched chains and rings.
hooks, shackles or swivel, permanently attached thereto, a test load not less than 50 per cent in excess of the safe working load shall be applied.
(e) In the case of a pulley block fitted with a bucket, the bucket shall be tested and the load applied to the bucket when testing that block will be accepted as test load of the bucket.
(f) In the case of sling having two legs, the safe working load shall be calculated when the angle between the legs is 90 degree. In case of multi-legged slings the safe working load shall be calculated as per national standards.
(g) Every lifting beam, lifting frame, container spreader bucket, tub. or other similar devices shall be subjected to a test load which shall not be less than the load as specified in the following table:— -102- TABLE Proposed safe working load Test load (in tonnes) (in tonnes) Upto 10 .. 2 x safe working load 10 to 160 .. (1.04 x safe working load)+9.6 Above 160 .. 1.1 x safe working load.
(h) Wire ropes.—In the case of wire ropes a sample shall be tested to destruction.
The test procedure shall be in accordance with recognised national standards.
The safe working load of the rope is to be determined by dividing the load at which the sample broke by a co-efficient of utilisation, determined as specified in the following table:-- TABLE Item . Co-efficient of Utilisation
(1) (2)
(a) Wire rope forming part of sling safe working load of the sling; safe working 5 load upto and equal to 10 tonnes Safe working load above 10 tonnes and upto and equal to 160 tonnes. 10 (8.85 x safe working load +1910 Safe working load above 160 3
(b) Wire rope as integral part of a lifting appliance safe working load of the lifting appliance: Safety working load upto and equal to 160 tonnes 10 (8.85 x safe working load +1910 Safe working load above 160 tonnes. 3
(i) Before any test is carried out, a visual inspection of the lifting appliance, or lifting gear involved shall be conducted and any visible defective gear shall be replaced or renewed.
(j) After being tested, all the lifting gears shall be examined to see whether any parts have been injured or permanently deformed by the test.
-103- Procedure for testing:
(3) Derricks.- (a) A Derrick shall be tested with its boom at the minimum angle to the horizontal for which the derrick is designed (generally 15 degrees) or at such greated angle as may be agreed. The angle at which the test has been carried out shall be mentioned in the test certificate. The test load shall be applied by hoisting movable weights. During the test, the boom shall be swung with the test load, as far as practicable, in both directions.
(b) A derrick boom, designed to be raised with power, with the load suspended, shall, in addition to the test at (a), be raised (with the load suspended) to its maximum working angle to the horizontal and the two outermost positions.
(c) While test loading of a heavy lift derrick the competent person responsible for tests using movable weights shall ascertain from the owner of the vessel or floating platform that the stability of the vessel or platform is adequate for the test.
(4) The derricks tested under clause (3) shall not be used in union purchase rigs unless,-
(a) the derricks rigged in union purchase are tested with the test load appropriate to the safe working load in union purchase (at the designed headroom and with the derrick booms their approved working positions):
(b) the safe working load of that derrick in union purchase rig has also been specified by a competent person in a report in Form-V:
(c) any limitations or conditions specified in the said report are complied with; and
(d) the two hoist ropes are coupled together by a suitable swivel assembly.
Explanation,--The safe working loads of derricks (for each method of rig including union purchase) shall be shown or the Certificate of test and marked on the derrick booms.
(5) Lifting appliances.- (a) The test loads shall be lifted and swung . as far as possible, in both directions. If the jib or boom of the crane has a variable radius, it shall be tested with test loads at the maximum and minimum radii. In case of hydraulic cranes when owing to the limitation of pressure, it is impossible to lift a test load in accordance with table under item
(1). it will be sufficient to lift the greatest possible load which shall be more than safe working load.
(b) The test shall be performed at maximum, minimum and intermediate radius points as well as such points in the arc of rotation, as the competent person may decide. The test shall consist of hoisting, lowering, breaking and swinging and swinging through all positions and operations normally performed. An additional test shall be made by operating the machinery at maximum working speed with the safe working load suspended.
(6) Use of spring or hydraulic balances, etc. for test loading.- All tests shall normally be carried on with the help of dead weights. In case of periodical test. replacements or renewals, test load may be applied by means of suitable springs or hydraulic balances. In such case. test load shall be applied with the boom, as far out as practicable, in both directions. The test shall not be taken as satisfactory unless the balance has been certified for accuracy by the -104- competent authority within 20 percent and the pointer of the machine has remained constant at the test load for a period of at least five minutes.
(7) Testing machines and dead weights.- (a) A suitable testing machine shall be used for testing of chains, wire ropes and other lifting gears:
(b) Testing machined and balances to be used in test loading, testing and checking shall not be used unless they have been certified for accuracy at least once in the preceding twelve months by the competent authority; and
(c) Movable weights used for the test loading of the lifting appliances having a safe working load not exceeding twenty tonnes shall be checked for accuracy by means of suitable weighing machine of certified accuracy.
(8) Through examination after testing or test loading.- After being test loaded, every lifting appliance and associated gear shall be thoroughly examined to see that no part has been damaged or permanently deformed during the test. For this purpose, the lifting appliance or gear shall be dismantled to the extent considered necessary by the competent person.
SCHEDULE-II.
Notifiable Occupational Diseases in Building and other Construction work.
[(See rule 230(a)]
1. Occupational dermatitis.
2. Occupational Cancer.
3. Asbestos.
4. Silicosis.
5. Lead poisoning including poisoning by any preparation or compound of lead or their sequelae.
6. Benzene poisoning, including poisoning by any of its homologues, their nitro or amino derivatives or its sequelae.
7. Occupational asthama.
8. Pesticide poisoning.
9. Carbon monoxide poisoning.
10. Toxic Jaundice.
11. Toxic anaemia.
12. Compressed air illness (Caissons disease).
12. Noise induced hearing loss.
13. Isocyanates poisoning.
14. Toxic nephritis.
-105-
SCHEDULE-IlI Contents of a First-aid Box [See rule 231 (b)]
(k) A sufficient number of eye wash bottled filled with distilled water suitable liquid clearly indicated by a distinctive sign which shall be visible at all times.
(ii) 4 percent xylocaine eye drops, and boric acid eye drops and soda by carbonate eye drops.
(iii) Twenty four small sterilized dressings.
(iv) Twelve medium size sterilised dressings.
(v) Twelve large size sterilised dressings.
(vi) Twelve large size sterilised burn dressings.
(vii) Twelve (fifteen) and packets of sterlised cotton wool.
(viii) One (Two hundred millilitre) bottle of certimide solution (1 per cent) or suitable antiseptic solution.
(ix) One (two hundred millilitre) bottle of mercurochrome (2 percent) solution in water.
(x) One (one hundred twenty millilitre) bottle of sal-volatile having the doses and mode of administration indicated on the label.
(xi) One pair of scissors.
(xii) One roll of adhesive plaster (six centimeter x one metre)
(xiii) Two rolls of adhesive plaster (two centimeters x one metre)
(xiv) Twelve pieces of sterilised eye pads in separate sealed packets.
(xv) A bottle containing hundred tablets (each of three hundred twenty five milligram) of aspirin or any other analgesic.
(xvi) Twelve roller bandages ten centimeters wide.
(xvii) Twelve roller bandages five centimeters wide.
(xviii) One tourniquet.
(xix) A supply of suitable splints.
(xx) Three packets of safety pins.
(xxi) Kidney tray.
(xxii) A snake bite lancet.
(xxiii) One (thirty milliltire) bottle containing potassium permanganate crystals.
(xxiv) One copy of first-aid leaflet issued by the Directorate General.
(xxv) Six triangular bandages.
-106-
(xxvi) Two pairs of suitable, sterilised, latex hand gloves.
SCHEDUI.E - IV (Articles for ambulance room) {See rule 226 (c)}
(i) A glazed sink-with hot and cold water always available.
(ii) A table with a smooth top at least 180/ centimeters x 105 centimeters.
(iii) Means for sterilising instruments.
(iv) A couch.
(v) Two stretchers.
(vi) Two buckets or containers with close fitting lids.
(vii) Two rubber hot water bags.
(viii) A kettle and spirit stove or other suitable means of boiling water.
(ix) Twelve plain wooden splints 900 centimeters x 100 centimeters x 6 centimeters.
(x) Twelve plain wooden splints 350 centimeters x 75 centimeters x 6 centimeters.
(xi) Six plain wooden splints 250 centimeters x 50 centimeters 12 centimeters.
(xii) Six woolen blankets.
(xiii) Three pairs artery forceps.
(xiv) One bottle of spiritus annemiae aremations (120 millilitre).
(xv) Smelling salt (60 grams).
(xvi) Two medium size sponges.
(xvii) Six hand towels.
(xviii) Four kidney trays.
(xix) Four cakes of toilet, preferably antiseptic soap.
(xx) Two glass tumblers and two wine glasses.
(xxi) Two clinical thermometres.
(xxii) Two tea spoons.
(xxiii) Two graduated (120 millilitre) measuring glasses.
(xxiv) Two minimum measuring glasses.
(xxv) One wash bottle (1000 cubic centimetre) for washing eyes.
(xxvi) One bottle (one litre) carbolic lotion 1 in 20.
(xxvii) Three chairs.
(xxviii)One screen.
(xxix) One electric hand torch.
-107-
(xxx) Four first-aid boxes or cupboards stocked to the standards prescribed in the Schedule III.
(xxxi) An adequate supply of tetanus toxide.
(xxxii) Injections-morphia. pethidine. atrophine. adrenaline, coramine, novacaine (6 each).
(xxxiii)Cramine liquid (60 millilitre).
(xxxiv) Tablets - antihistaminic antispasmodic (25 each)
(xxxv) Syringes with needles-2 cubic centimetres, 5 cubic centimetres, 10 cubic centimetres and 500 cubic centimetres.
(xxxvi) Three surgical scissors.
(xxxvii) Two needle holders, big and small.
(xxxviii) Suturing needles and materials.
(xxxxi) Three dissecting forceps.
(xl) Three dressing forceps.
(xli) Three scalpels.
(xlii) One stethoscope and a B.P. apparatus.
(xliii) Rubber bandage - pressure bandage.
(xliv) Oxygen cylinder with necessary attachments.
(xlv) Atropine eye ointments.
(xlvi) I.V. Fluids and sets 10 numbers.
(xlvii) Suitable, foot operated covered, refuse containers.
(xxxxviii )Adequate number of sterilised. paired, latex hand gloves.
SCHEDULE - V.
Contents of Ambulance Van or Carriage.
[See rule 227] The Ambulance Van shall have equipment prescribed as under,—
(a) General.- A portable stretcher with folding and adjusting devices with the head of the stretcher capable of being tilted upward. Fixed suction unit with equipment. Fixed oxygen supply with equipment. Pillow with case, sheets, blankets, towels, emergency bag, bed pan, urinal glass.
(b) Safety Equipment.- Flaros with life of three thousand minutes, floor lights, flash lights, fire extinguishers (dry powder type), insulated guntlets -108-
(c) Emergency Care Equipment.- (i) Resuscitation: Portable suction unit. portable oxygen unit. bagvalve mask. hand operated artificial ventilation unit, airways, mouthgag tracheostomy adapters, short spine board. l.V. Fluids with administration unit. B.P.
manometer, cuff stethoscope.
(ii) Immobolisation- Long and short padded boards, wire ladder splints, triangular bandage - long and short spine boards.
(iii) Dressing.- Gauze pads- 100 millimeter x 100 millimeter universal dressing 250 x 1000 millimeters roll of aluminium foils- soft roller bandages 150 millimeter x 5 millimeter yards adhesive tape in 75 millimeter roll of safety pins, bandage sheets, burn sheets.
(iv) Poisoning.- Syrup of Ipecac, activated charcoal prepacketed does, snake bite kit. drinking water.
(v) Emergency Medicine.- as per requirement (under the advice of construction Medical Officer).
SCHEDULE-VI .
Permissible Exposure in cases of Continuous Noise.
(See rule 34) Total time of exposure (continuous /or number of short -term exposures) per day (in hours) Sound pressure level.(in dBA)
(1) (2) 8 90 6 92 4 95 3 97 2 100 1 1/2 102 1 105 3/4 107 1/2 110 1/4 115
Explanations- (1) No exposure in excess of 115 dBA is to be permitted.
(2) For any period of exposure falling in between any figure and the next higher or lower figure as indicated in column (1), the permissible sound pressure level is to be determined by extrapolation on a proportionate basis.
-109-
SCHEDULE-VII.
Periodicity of Medical examination of building workers.
{See rule 81 (iv) and 223 (a) (iii)}
1. The employer shall arrange a medical examination of all the building workers employed as drivers, operators of lifting appliances and transport equipment before employing, after illness or injury, if it appears that the illness or injury might have affected his fitness and thereafter, once in every two, years upto the age of forty and once in a year, thereafter.
2. Complete and confidential records of medical examination shall be maintained by the employer or the physician authorised by the employer.
3. The medical examination shall include,--
(a) full medical and occupational history;
(b) clinical examination with particular reference to,—
(i) General Physique.
(ii) Vision.- Total visual performance and standard orthorator like Titmusvision Tester should be estimated and suitability for placement ascertained in accordance with the prescribed job standards.
(iii) Hearing.- persons with normal hearing must be able to hear a forced whisper at twenty four feet. Person using hearing aids must be able to hear a warning shout under noisy working conditions.
(iv) Breathing- Peak flow rate using standard peak flow meter and the average peak flow rate determined out of these readings of the test performed. The results recorded at pro-placement medical examination could be used as standard for the same individual at the same altitude for reference during subsequent examination.
(v) Upper limbs.- Adequate arm function and grip (both arms).
(vi) Lower Limbs.- Adequate leg and foot function.
(vii) Spine.- Adequately flexible for the job concerned.
(viii) General.- Mental alertness and stability with good eye, hand and foot coordination.
(c) Any other tests which the examining doctor considers necessary.
-110-
SCHEDULE-VIII Number of safety officers, qualification, duties, etc.
[(See Rule 209 (1) and 209 (2)] Appointment of Safety Officers.
Number of Safety Officers:- Within six months of coming into operation of these rules, every establishment employing more than five hundred building workers and every other employer of building worker shall appoint safety officers, as laid down in the scale given below:-
(1) Upto 1000 building workers - one safety officer.
(2) Upto 2000 building workers - two safety officers.
(3) Upto 5000 building workers- three safety officers.
(4) Upto 10,000 building workers-four safety officers.
For every additional 5000 building workers or part thereof- one safety officer.
Any appointment, when made shall be notified to the lnspector having Jurisdiction in the area, giving full details of the qualifications, terms and conditions of service of such safety officer.
Qualification- (a) A person shall not be eligible for appointment as a safety officer unless he,—
(i) possesses a recognised degree in any branch of engineering or technology or architecture and had a practical experience of working in a building or other construction work in a supervisory capacity for-a period of not less than two years or possesses a recognised diploma in any branch of engineering or technology and has had practical experience of building or other construction work in a supervisory capacity for a period of not less than five years;
(ii) possesses a recognised degree or diploma in industrial safety with at least one paper in construction safety (as an elective subject); and
(iii) has adequate know ledge of Tamil.
(b) Notwithstanding the provision contained in clause (a), any person who,--
(i) possesses a recognised degree or diploma in engineering or technology or architecture and has had experience of not less than five years in the field, dealing with the administration of Factories Act, 1948 or the Dock Workers (Safety, Health and Welfare) Act, 1986 or the Building and Other Construction Workers (Regulation of Employment and Conditions of Service) Act, 1996; or -111-
(ii) possesses a recognised degree or diploma in engineering or technology and has had experience of not less than five years or has undergone training in education, consultancy or research in the field of accident prevention in industry, port or in any institution or an establishment dealing with building or other construction work;
shall also be eligible for appointment as a safety officer.
Provided that, in case of person who has been working as safety officer in industry or port. institution or an establishment dealing with building or other construction work for a period of not less than three years on the date of commencement of these rules. the Chief Inspector of Building and other Construction Work may, subject to such conditions that he may specify, relax all or any of the above said qualification.
Conditions of Service,-- (a) where the number of safety officers appointed exceeds one, one of them shall be designated as Chief Safety Officer and shall have the status higher than the others. The Chief Safety Officer shall be in over all charge of the safety functions as envisaged in sub-clause (iv) and also other safety officers working under -his control.
(b) the Chief Safety Officer or the Safety Officer, where only one safety officer is appointed. shall be given the status of a Senior Executive and he shall work directly under the control of his Chief Executive. All other safety officers shall be given appropriate status to enable them to dispatch their functions effectively.
(c) the scale of pay and allowances to be granted to the safety officers including the Chief Safety Officer and the other conditions of their service shall be the same as those of the officers of corresponding status of the establishment in which they are employed.
Duties of Safety Officer.- (a) The duties of a safety officer shall be to advise and assist the employer in the fulfillment of his obligations, statutory or otherwise concerning preventive of personal injuries and maintaining a safe working environment. The duties shall include the following namely;-
(i) to advise the building workers in planning and organising measures necessary for effective control of personal injuries:
(ii) to advise on safety aspects in a building or other construction work and to carryout detailed safety studies of selected activities;
(iii) to check and evaluate the effectiveness of action taken or proposd to be taken to prevent personal injuries;
(iv) to advise purchasing and ensuring quality of personal protective equipment confirming to national standards;
(v) to carryout safety inspections of building or other construction work in order to observe the physical conditions of work and the work -112- practices and procedures followed by building workers and to render advice on measures to be adopted for removing unsafe physical conditions and preventing unsafe actions by building workers;
(vi) to investigate all fatal and other selected accidents;
(vii) to investigate all cases of occupational diseases contracted and reportable dangerous occurrences;
(viii) to advise on the maintenance of such records as are necessary with regard to accidents, dangerous occurrences and occupational diseases;
(ix) to promote the working of safety committees and to act as an advisor to such committees.
(x) to organise, in association with concerned departments, campaigns, competitions, contests and other activities which will develop and maintain the interest of building workers in establishing and maintaining safe conditions of work and procedures;
(xi) to design and conduct, either independently or in collaboration with other agencies suitable training and educational programmes for prevention of accidents to building workers;
(xii) to frame safe rules and safe working practices in consultation with senior officials of the establishment; and
(xiii) supervise and guide safety precautions to be taken in building and other construction work of the establishment.
Facilities to be provided to safety officers.- The employer shall provide each safety officer with such facilities, equipment and information that are necessary to enable him to despatch his duties effectively.
Prohibition of performance of other duties.- No safety officer shall be required or permitted to do any work which is unconnected to, inconsistent with or detrimental to the performance of the duties prescribed in this Schedule.
Exemptions.- The Chief Inspector of Building and other Construction Work may, in writing, exempt any employer or group of employees from any or all of the provisions of these rules subject to compliance with such alternative arrangements as may be approved and notified by him in the order of such exemption.
-113-
SCHEDULE -IX (See rule-225) Hazardous process.
(1) Roof work.
(2) Steel erection.
(3) Work under and over water.
(4) Demolition.
(5) Work in confined spaces.
SCHEDULE-X.
[See rule 225 (b)] Services and facilities to be provided in occupational health centres.- (1) One full time construction medical officer for building or other construction work, employing workers upto one thousand and one additional construction medical officer for every additional one thousand workers or part thereof.
(2) The staff, including one nurse, one dresser-cum-compounder, one sweeper-cumward boy with each construction medical officer for full work hours.
(3) The occupational health centre with a floor area of minimum fifteen square metre constituting two rooms with smooth walls and impern service, adequately illuminated and ventilated.
(4) Adequate equipment for day to day treatment.
(5) Necessary equipment to manage any medical emergency.
SCHEDULE-XI [See rule 119 (2) and 225 (c)] Qualification of construction medical officer - (1) MBBS degree from a medical institute recognised by the Medical Council of India; and
(2) Diploma in industrial health or equivalent post graduate certificate of training in industrial health or health.
(3) A medical officer having working experience in organisation / establishments involved in policy, execution and advice and safety and health of workers employed in mines, ports and docks. factories and building and other construction work, for a period of not less than three years may, subject to the satisfaction of the Chief Inspector of Building and other Construction Work not be required to possessing the training referred to in item (2) above.
-114-
(4) The syllabi of the courses leading to the above certificates and the organisation conducting such courses shall be approved by the Government who may also from time to time prepare a panel of such organisations.
(5) Complete particulars including name, qualification and experience of the construction medical officer will be intimated to the inspector having jurisdiction.
SCHEDULE-XII.
[See rule 152(a)] PERMISSIBLE LEVELS OF CERTAIN CHEMICAL SUBSTANCES IN THE WORK ENVIRONMENT Sl.
No Substance Permissible limit of exposure Time-weighted average concentration (TWA) (8 hours) Short-term exposure limit (STEL) (15 minutes)* ppm Mg/m³** ppm Mg/m³** 1 2 3 4 5 6 01 Acetaldehyde 100 180 150 270 02 Acetic acid 10 25 15 37 03 Acetone 750 1780 1000 2375 04 Aerolein 0.1 0.25 0.3 0.8 05 Acrylonitrile-Skin (S.C.) 2 4.5 - - 06 Aldrin-Skin - 0.25 - - 07 Allyl chloride 1 3 2 6 08 Ammonia 25 18 35 27 09 Aniline-Skin 2 10 - - 10 Anisidine (0-,p-isomers)- Skin 0.1 0.5 - - 11 Arsenic & soluble compounds (as As) - -.2 - - 12 Benzene (S.C.) 10 30 - - 13 Beryllium Compound (As be) (S.C.) - 0.002 - - 14 Boron trifluoride-C 1 3 - - 15 Bromine 0.1 0.7 0.3 2 16 Butane 800 1900 - - 17 2-Butanone MBK) (Methyl ethyl Ketone- 200 590 300 885 115 18 n-Butyl acetate 150 710 200 950 19 n-Butyl alcohol-Skin-0 50 150 - - 20 Sec/tert, Butyl acetate 200 950 - - 21 Butyl mercaptan 0.5 1.5 - - 22 Cadmium dust and salts (as Cd) - 0.05 - - 23 Calcium oxide - 2 - - 24 Carbary (sevin) - 5 - - 25 Carbofuran (Furadan) - 0.1 - - 26 Carbon disulphide-Skin 10 30 - - 27 Carbon monoxide 50 55 400 440 28 Carbon tetrachloride-- Skin (S.C.) 5 30 - - 29 Chlordane-Skin - 0.5 - - 30 Chlorine 1 3 3 9 31 Chlorobenzene (Monochlororbenzene) 75 350 - - 32 Chloroform (S.C.) 10 50 - - 33 Bis (Chloromethyl) ether (H.C.) 0.001 0.005 - - 34 Chromic acide chromates (as Cr,) (Water soluble) - 0.05 - - 35 Chromous salts (as Cr.) - 0.5 - - 36 Copper-fume - 0.2 - - 37 Cotton dust, raw - 0.2* - - 38 Cresol, all isomers-Skin 5 22 - - 39 Cyanides (as CN)-Skin - 1 - - 40 Cyanogen 10 20 - - * line free dust as measured by the vertical eluviator cotton-dust sampler.
(1) (2) (3) (4) (5) (6)
41. Dichlorodiphenyl trichloroethane - 1 - -
42. Demeton-Skin 0.01 0.01 - -
43. Diazinion-Skin - 0.01 - -
44. Dibutyl Phthalate - 5 - -
45. Dicholorvos (DDVP)-Skin 0.01 1 - -
46. Dieldrin-Skin - 0.25 - -
47. Dintrobenzene (all isomers)-Skin 0.15 1 - -
48. Dinitroteoluene-Skin - 1.5 - -
49. Dipheny (Diphenyl) 0.2 1.5 - -
50. Endosulfan (Thiodan)-Skin - 0.1 - -
51. Endrin-Skin - 0.1 - - -116-
52. Ethyl acetate 400 1400 - -
53. Ethyl alcohol 1000 1900 - -
54. Ethylamine 10 18 - -
55. Fluordies (as F) - 2.5 - -
56. Flucrine 1 2 2 4
57. Formaldehyde (S.C.) 1.0 1.5 2 3
58. Formic acid 5 9 - -
59. Gasoline 300 900 500 1500
60. Hydrazine-Skin (S.C.) 0.1 0.1 - -
61. Hydrogen Chloride-C 5 7 - -
62. Hydrogen Cyanide-Skin-C 10 10 - -
63. Hydrogen fluorine (as F).C 3 2.5 - -
64. Hydrogen peroxide 1 1.5 - -
65. Hydrogen sulphide 10 14 15 21
66. Iodine-C 0.1 1 - -
67. Iron Oxide Fume (Feo) (as Fe) - 5 - -
68. Isoamyl acetate 100 525 - -
69. Isoamyl alcohol 100 360 125 450
70. Isobuty alcohol 50 150 - -
71. Lead, inorg, dusts and fumes (as Pb) - 0.15 - -
72. Lindane-Skin - 0.5 - -
73. Malathion-Skin - 10 - -
74. Manganese dust and compounds (as Mn)-C - 5 - -
75. Manganese fume (as Mn) - 1 - -
76. Mercury (as Hg)-Skin
(i) Alkyl compounds - 0.01 - 0.30
(ii) All forms except alkyl vapour - 0.05 - -
(iii) Atyl and inorganic compound - 0.1 - -
77. Methyl alchol (Methanol)-Skin 200 0.260 250 310
78. Methyl cellosolve (2-Methoxy-ethanol)-Skin 5 16 - -
79. Methyl isobutylketone 50 305 75 300
80. Methyl isocyanate-Skin 0.02 0.05 - -
81. Napthalene 10 50 15 75
82. Nickel carbonyl (as Ni) 0.05 0.35 - -
83. Nitric acid 2 5 4 10
84. Nitric Oxide 25 30 - -
85. Nitrobenzene-Skin 1 5 - -
86. Nitrogen dioxide 3 6 5 10
87. Oil mist, mineral - 5 - 10
88. Ozone 0.1 0.2 0.3 0.6
89. Parathion-Skin - 0.1 - -
90. Phenol-Skin 5 19 - -
91. Phorate (Thimet)-Skin - 0.05 - 0.2
92. Phosgene (Carbonyl Cholride) 0.1 0.4 - -
93. Phosphine 0.3 0.4 1 1
94. Phosphoric acid - 1 - 3 -117-
95. Phosphorus (Yellow) - 0.1 - -
96. Phosphorus Pentachloride 0.1 1 - -
97. Phosphorus trichloride 0.2 1.5 0.5 3
98. Pieries acid-Skin - 0.1 - 0.3
99. Pyridine 5 15 - -
100. Silane (Silicon tetrahy dride) 5 7 - -
101. Sodium hydroxide-C - 2 - -
102. Styrene,monomer (Phenylethylene) 50 215 100 425
103. Sulphur dioxide 2 5 5 10
104. Sulphur hexafluroride 1000 6000 - -
105. Sulphuric acid - 1 - -
106. Tetraethyl lead (as Pb)-Skin - 0.1 - -
107. Tolune 100 375 150 560
108. O-Toluidine-Skin (S.C.) 2 9 - -
109. Tributyl phosphate 0.2 2.5 - -
110. Trichloroethylene 50 270 200 1080
111. Uranium, natural (as U) - 0.2 - 0.6
112. Vinyl chloride (H.C.) 5 10 - -
113. Welding fumes - 5 - -
114. Xylene (o-m-, p-isomers) 100 435 150 655
115. Zinc Oxide
(i) Fume - 5.0 - 10
(ii) Dust (Total Dust) - 10.0 - -
116. Zirconium compounds (as Zr.) - 5 - 10 ppm : Parts of vapour or gas per million parts of contaminated air by volume at 25ºC and 760 mm of Hg.
mg/m³ : Milligram of substance per cubic metre of air.
* : Not more than 4 times a day with atleast 60 min. interval between successive exposures.
**Mg/M³ : Molecular weight x ppm
24.45 'c' : denotes Ceiling Limit.
'Skin' : Denotes potential contribution to the overall exposure by the cutaneous route including mucous membranes and eye.
'S.C.' : Denotes Suspected Human Careinogen.
'H.C.' : Denotes Confirmed Human Careinogen.
Substance Permissible time-weighted average Concentration (TWA) (8.Hrs.)
Silica, S1O2
(a) Crystalline i) Quartz -118-
(1) In terms of dust count 10600 ----------------------- mppcm % Quartz + 10
(2) In terms of respirable dust 10 ------------------------------- mg/m³ % respirable Quartz + 2
(3) In terms of total dust 30 ---------------------- mg/m³ % Quartz + 3 ii) Cristobalite Half the limits given against quartz.
iii) Tridymite Half the limits given against quartz.
iv) Silica, fused Same limits as for quartz.
v) Tripoli Same limits as in formula in item (2) given against quartz.
b) Amorphous Silicates Asbestos (H.C.)
10 mg/m³, Total dust.
* 2 fibres/ml, greater than 5µm in length and less than 3µm in breadth with length to breadth ratio equal to or greater than 3:1 Portland Cement 10 mg/m³, Total dust containing less than 1% quartz.
Coal Dust 2 mg/m³, respirable dust fraction containing less than 5% quartz.
---------------------------------------------------------------------------------------------------------------- Mppcm : Million particles per cubic metre of air, based on impinger samples counted by light-field techniques.
* : As determined by the membrane filter method at 400-450 x magnification (4 mm objective) phase contrast illumination.
SCHEDULE - XIII Form-I [ See rule 23(1) ] Application for registration of establishments employing building (or) other Construction workers:-
1. Name and location of the establishment where building other construction work is to be carried on.
2. Postal address of the establishment.
-119-
3. Full name and permanent address of the establishment, if any.
4. Full name and address of the Manager or person responsible for the supervision and control of the Establishment.
5. Nature of building or other construction work carried/is to be carried on in the establishment.
6. Maximum number of building workers to be employed on any day.
7. Estimated date of commencement of building or other construction work.
8. Estimated date of completion of the building or other construction work.
9. Particulars of demand draft, enclosed (name of the Bank, amount, demand draft No. and date).
Declaration by the employer-
(i) I hereby declare that the particulars given above are true to the best of my knowledge and belief.
(ii) I undertake to abide by the provisions of the Building and other Construction Workers (Regulation of Employment and Conditions of Service) Act, 1996 and the Rules made thereunder.
Signature of the Principal Employer.
Seal and Stamp Office of the Registering Officer appointed under the Building and other Construction Workers (Regulation of Employment and Conditions of Service) Act, 1996 and the rules made thereunder.
Date of receipt of application:
FORM - II [ See rule 24(1)] Date A Certificate of Registration is hereby granted under sub-section (3) of section 7 of the Building and Other Construction Work (Regulation of Employment and Conditions of Service) Act, 1996 and the rules made thereunder, to M/s… having the following particulars subject to conditions laid down in the Annexure:-
1. Postal Address/location where building or other construction work is to be carried on by the Employer.
-120-
2. Name and address of employer including location of the building and other construction work.
3. Name and permanent address of the establishment.
4. Nature of work in which building workers are employed or are to be employed.
5. Maximum number of building workers to be employed on any day by the employer.
6. Probable date of commencement and completion of work.
7. Other particulars relevant to the employment of building workers.
Signature of Registering Officer with Seal.
ANNEXURE The registration granted herein above is subject to the following conditions, namely:-
(a) the certificate of registration shall be non-transferable.
(b) the number of workmen employed or building workers in the establishment shall not, on any day, exceed the maximum number specified in the certificate of registration;
(c) save or provided in these rules, the fees paid for the grant of registration certificate shall be non-refundable.
(d) the rates of wages payable to building workers by the employer shall not be less than the rates prescribed under the Minimum Wages Act, 1948 (Central Act XI of 1948) for such employment where applicable, and where the rates have been fixed by agreement, settlement or award not less than the rates so fixed; and
(e) the employer shall comply with the provisions of the Act and the rules made thereunder.
-121- FORM - III REGISTER OF ESTABLISHMENTS [ See rule 24(2) ] Serial Number Registration Number and Date Name and address/location of the establishment registered, where a building or other construction work is to be carried on Name of the employer and his address Nature of building or other constructio n work.
Name and permanent address of establishment Probable date of commence -ment of Work.
Maximum Number of building workers to be employed on any day.
Probable duration of building or other constructio n work and probable date of completion.
Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) -122- FORM - IV.
[ See rules 26(3) and 239(1) ] Notice of commencement/Completion of Building or other construction work.
(1) (i) Name and address (Permanent) of the establishment.
(ii) Name of the employer and address……………………….
(2) Name and situation of place where the building and other construction is proposed to be carried on.
(3) Number and date of Certificate of registration………………
(4) Name and address of the person incharge of the construction work.
(5) Address to which the communications relating to building or other construction work may be sent.
(6) Nature of work involved and the facilities including plant or machinery provided.
(7) The arrangement storage of explosive, if any, to be sued in building or other construction work.
(8) In case the notice is for commencement of work, the approximate duration of work.
I/We hereby intimate that the building or other construction work (Name of work) having registration No… .......................... dated ……………. is likely to commence/is likely to be completed with effect from ……………….. (date)/ on .................. (date).
Signature of the Employer.
To, The Inspector, ……………………………… ……………………………… -123- FORM - V [ See rule 74(b), Schedule I ] Certificate of Initial and periodical Test and Examination of winches, Derricks and their Accessory Gear.
Test Certificate No…………………………………………..
(a) In case of construction site, name of the construction site where lifting appliances are fitted/installed/located.
Situation and description of lifting appliances and Gear with distinguishing numbers or marks (if any) which have been tested, thoroughly examined.
Angle to the horizontal of derrick boom at which test load applied.
Test load applied Safe working load at the angle shown in column (2) Name and address of public service, association, company or firm or testing establishment making the test and examination.
Name and position of the competent person of public service, association, company or firm or testing establishment.
(1) (2) (Degrees)
(3) (Tonnes)
(4) (Tonnes)
(5) (6) I certify that on the …………..day of .................... the lifting appliance shown in column (1) together with its necessary gear was tested in the manner set forth overleaf in my presence; that a careful examination of the said lifting appliances after the test showed that it had withstood the test load without injury or permanent deformation; and that the safe working load of the said lifting appliance and accessory gear is as shown in column(4).
Signature of the Competent Person Date Seal Registration/Authority number of the Competent Person.
-124- FORM - VI.
[ See rules 56 and 74 (b) ] Certificate of initial and Periodical test and Examination of cranes or Hoists and their Accessory gear.
Test Certificate No…………………………….
(a) Name of the construction site where cranes or hoists are fitted/installed/located.
Situation and description For jib cranes radius at the test load was applied Test load applied Safe working load for jib cranes at radius shown in column (2) Name and address Public service, association or firm or testing establishment making the test and examination.
Name and position of competent person of public service, association, company or firm or testing establishment.
(1) (2) (Metres)
(3) (Tonnes)
(4) (Tonnes)
(5) (6) I certify that on the ……………. day of ...................... the above lifting appliances together with its accessory gear, was tested in the manner set forth overleaf; that a careful examination of the said lifting appliance and gear after the test showed that it had withstood the test load without injury or permanent deformation; and the safe working load of the said lifting appliance and gear is as shown in column(4).
Signature of the Competent Person *Seal Date (See note 3) Registration/Authority number of the Competent Person -125- FORM-VII.
[ See rules 70 and 74(b) ].
Certificate of Initial And Periodical Test And Examination of Loose Gears.
Test Certificate No………………………
(a) Name of the construction site where loose gears fitted/installed/located:
Distinguishing number of Mark Description dimension and material of gear device Number tested Date of test Test load applied (tonnes) Safe working load (SWL) (Tonnes) Name and address of manufacturer or suppliers.
Initial test and examination certificate No.
and date (only in case of periodical test and examination) Name and address of public service association, company or firm or testing establishment making the test and examination Name and position competent person Public service association, company or firm or testing establishment.
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) I certify that on the ……………. day of ........................ 20 … the above gear was tested and examined in the manner set forth overleaf; that the examination showed the said gear/device withstood the test load without injury or deformation and that the safe working load of the said gear/ device is as shown in column(6).
Signature of the Competent Person Seal Date Registration/Authority number of the Competent Person.
-126- FORM - VIII [ See rule 74 (b) ] Certificate of test and Examination of wire-ropes before being taken into use Test Certificate No…………………..
(1) Name and address of maker or supplier.
(2) (a) Circumference/diameter of rope
(b) Number of strand
(c) Number of wire per strand
(d) Lay
(e) Core
(3) Quality of wire (e.g. Best Plough steel)
(4) (a) Date of test of sample of rope
(a) Load at which sample broke (tonnes)
(b) Safe working load of rope (tonnes)
(c) Intended use
(5) Name and address of public service, association, company or firm or testing establishment making the test and examination.
(6) Name and position of Competent Person in public service, association, company or firm or testing establishment making the test and examination.
I certify that the above particulars are correct, and the test and examination were carried out by me and no defect Effecting its safe working load (SWL) were found.
Signature of the Competent person Seal Date Registration/Authority number of the Competent Person.
-127- FORM - IX [ See rule 74 (b) ] CERTIFICATE OF ANNEALING OF LOOSE GEARS Test Certificate No……………………
(a) Name of the Construction site where loose gears are fitted/installed/located:
Distinguishing number or mark Description of gear Number of the certificate of test and examination Number annealed Date of annealing Detects found in careful inspection after annealing Name and address of public service association, company, or firm or testing establishment, carrying out the annealing and inspection Name and position of the competent person of public service association company or firm or testing establishment.
(1) (2) (3) (4) (5) (6) (7) (8) I certify that on the date shown in column (5) the gear described in columns (1) to (4) was effectually annealed under my supervision that after being so annealed every article was carefully inspected: and that no defects affecting its safe working conditions were found other than those indicated in column (6).
Signature of the Competent Person Seal Date:
Registration/Authority of the Competent Person.
-128- FORM - X [ See rule 73 ] Certificate of Annual Thorough examination of loose Gears Exempted from Annealing.
(a) Name of the Construction site where loose gears are fitted/installed/located.
Distinguishing Number of Mark Description of gear Number Certificate of initial and periodical test and examination Remarks Name and address of public service, association, company of firm or testing establishment making the test and examination Name and position of competent person of public service, association company or firm or testing establishment.
(1) (2) (3) (4) (5) (6) I certify that on the ……………….. the day of............................ the above gear, described in column (2) was thoroughly examined: and that no defects affecting its safe working condition were found other than those indicated in column (4).
Signature of the Competent Person Seal Date:
Registration/Authority number of the Competent Person.
-129- FORM - XI [ See rule 223(c) ] CERTIFICATE OF MEDICAL EXAMINATION
1. Certificate Serial No……………………………….
Date…………………….. Date…………………..
2. Name………………………………..
Identification marks (1) ………………………..
(2) ………………………..
3. Father's Name………………………….
4. Sex……………………
5. Residence…………………….son/daughter or …………………..
6. Date of birth, if available ………………………………….
and/or certificate age……………………………………….
7. Physical Fitness I hereby certify that I have personally examined (name) ……………..
son/daughter/wife of …………………… residing at …………………. who is desirous of being employed in building and construction work and that his/her age as nearly as can be ascertained from my examination is .......................... years and that he/she is fit for employment in …………….. as an adult/adolescent.
8. Reason for-
(1) refusal of certificate ……………………
(2) Certificate being revoked ……………………….
Signature/Left hand thumb Signature with Seal impression of building worker Medical Inspector/C.M.O.
Explanations:- 1. Exact details of cause of physical disability should be clearly stated.
2. Functional/productive abilities should also be stated if disability is stated/Productive.
-139- FORM - XII [ See rule 223 (d) ] Health Register (In respect of persons employed in Building and other construction work involving hazardous processes) Name of the Construction Medical Officer/Medical Inspector.
(a) Mr…………… From……………….. To………………..
(b) Mr……………. From……………….. To……………….
(c) Mr……………. From……………….. To……………….
Sl.
No.
Works No.
Name of building worker Sex Age (last birth day) Date of employment of present work Date of leaving or transfer to Other work.
(1) (2) (3) (4) (5) (6) (7)
1.
2.
3.
4.
5.
Reason for leaving, transfer or discharge Nature of job or occupation.
Raw material or by product handled Date of Medical examination by certifying surgeon Medical Inspector/CMO.
Results of medical examination If suspended from work, state period of suspension with detailed reasons.
(8) (9) (10) (11) (12) (13)
1.
2.
3.
4.
5.
Certified fit to resume duty on with signature of Medical Inspector/CMO.
If certificate of unfitness or suspension issued to worker
(14) (15)
1.
2.
3.
Signature with date of Medical Inspector/CMO.
Explanations:- (i) Column (8) - Detailed summary or reason for transfer or discharge should be stated.
(ii) Column (12) should be expressed as fit/unfit/suspended.
-131- FORM - XIII [See rule 230(a) ] Notice of poisoning or notifiable occupational diseases.
1. Name and address of the employer.
2. Name of the building worker and his work number if any.
3. Address of the building worker.
4. Sex and Age.
5. Occupation.
6. State exactly what the patient was doing at the time of contracting the disease.
7. Nature of poisoning or disease from which the building worker is suffering from.
Date: Signature of the employer/Chief Medical Officer.
Explanation:- When a building worker contracts any disease specified in Schedule- XII, a notice in this form shall be sent forthwith to the Chief Inspector of Building and other Construction Work.
-132- FORM - XIV [See rule 210(7) ] Report of Accidents and Dangerous Occurrences.
1. Name of the project/work
2. Location or project/work
3. Stage of construction work
4. Particulars of employer.
(a) Main contractor firm/Co.- (b) Sub-contractor's Particulars- Name Name Address Address Phone Numbers Phone Numbers Nature of business Nature of business
5. Particulars of injured person-
(a) Name (First) (Middle) (Signature)
(b) Home Address
(c) Occupation (d) Status of the worker- Casual Permanent
(e) Sex: Male Female (f) Age
(g) Experience
(h) Marital status: Married/Unmarried/Divorced
6. Particulars of Accident-
(a) Exact place where accident occurred
(b) Date
(c) Time
(d) What the injured person was doing at the time of accident?
(e) Weather condition
(f) How long employed by you for this particular job?
(g) Particulars of equipment/machine/tool involved and condition of the same after the accident occurred.
(h) Brief description of the accident.
-133-
7. Nature of injuries-
(a) Fatal
(b) Non-fatal
(c) If non-fatal, state precisely the nature of injuries (Describe in detail the nature of injury, for instance fracture of right arm, sprain etc.)
(d) First Aid: Given: Not given:
(e) If not given, the reasons
(f) Name and designation of the person by whom first aid was given.
(g) If admitted to hospital.
Name of the hospital:
Address of the hospital Phone Number Name of the Doctor
8. Mode of transport used Ambulance Truck Tempo Taxi Private Car
9. How much time was taken to shift the injured person?
If very late, state the reasons.
(b) How the reporting was made?
Telephone Telegram Special Messenger Letter
(c) Who visited the accident site first and what action was proposed by him?
(d) What are the action taken for the investigation of the accident by the employer?
(Describe about photographs/Video film/measurements taken etc.)
10. Particulars of the persons given witness-
(a) Name Address Occupation
1.
2.
3.
4.
(b) Whether Temporary Permanent -134-
11. Particulars in case of fatal- Date Time Whether registered with If yes, give Registration number.
Building and other Construction Workers Welfare Board
12. Dangerous Occurrences as covered under the Regulation No.
(Give details)
(a) Collapse or failure of lifting appliances, hoist, conveyors etc.
(b) Collapse or subsidence of soil, any wall, floor, galley etc.
(c) Collapse of transmission towers, pipeline, bridges etc
(d) Explosion of receiver, vessel etc.
(e) Fire and explosion
(f) Spillage or leakage of hazardous substances.
(g) Collapse, capsizing, toppling or collision of transport equipment.
(h) Leakage or release of harmful toxic gases at the construction site
(i) Failure of lifting appliance, loose gear, hoist or building and other construction work machinery, transport equipment etc.
13. Certificate from the Employer or authorised signatory- I certify that to the best of my knowledge and belief, the above particulars are correct in every respect.
Place: Signature:
Date: Designation:
copy communicated forwarded for information and follow-up action:-
1.
2.
3.
Explanation:- If more than one person is involved, then for each person information is to be filled-up in separate forms.
-135- FORM - XV [See rule 240 ] Register of Building and other Constructions Workers employed by the Employer.
Name and address Name and permanent of establishment address of establishment whether building and other construction work is to be carried on Nature and location of work ……………………..
Serial Number Name and surname of workman Age and Sex Father's/ Husband's Name Nature of Employment/ designation Permanent home address (Village and Taluk and district)
(1) (2) (3) (4) (5) (6)
1.
2.
3.
4.
Local address Date of commencement of employment Signature or thumb impression of workman Date of termination of employment Reasons for termination
(7) (8) (9) (10) (11)
1.
2.
3.
4.
If the building worker is/was beneficiary, the date of registration as a beneficiary, the registration number and the name of Welfare Board Remarks
(12) (13)
1.
2.
3.
4.
-136- FORM-XVI [See rule-241 (1)(a) ] Muster Roll Name and permanent address Name and address of the of the establishment establishment where building or other construction work is carried on is to be carried on Nature of building or other Name and address of the Employer construction work For the month of……………………… Sl.
No.
Name of the building worker Father's/ Husband's name Designation/ Nature of work Sex Date of Birth Period of work Dates Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9)
1.
2.
3.
4.
5.
-137- FORM - XVII [ See rule 241 (1)(a) ] Register of Wages Name and address of the establishment where building or other construction work is carried on Nature of building or other construction work Name and permanent address of Establishment Name and address of the Employer Wage Period: Monthly Sl.
No.
Name of workmen Serial No.
in the register of workman Designation/ nature of work done.
No. of days worked Units of work done Daily rate of Wage/Piece Rate
(1) (2) (3) (4) (5) (6) (7) Amount of wages earned Basic wages Dearness allowance Overtime Other cash payments (Nature of Payment to be indicated) Total Deductions if any, (indicate nature) Net amount paid Signature/ thumb impression of workman Initial of employer or his representative
(8) (9) (10) (11) (12) (13) (14) (15) (16) -138- FORM XVIII (SEE RULE 241 (1) (a) ) Form of Register of Wages-cum-Muster Roll.
Name and address of the Establishment Name and where building or other construction Permanent work is carried on. Nature of Building address of or other construction work. establishment Sl.
No.
(1) Sel.No. in Register of Building workers.
(2) Name of Employees
(3) Designation/ nature of work
(4) Daily attendence/ units worked
(5) Total attendance/ units of work done
(6) Daily rate of wages/ piece rate
(7) AMOUNT OF WAGES EARNED Basic Wages
(8) Dearness allowances
(9) Overtime
(10) other cash payment (nature of payment to be indicated)
(11) Total
(12) Deductions if any (indicate nature)
(13) Net amount paid
(14) Signature/ Thumb impression of workman
(15) Initial of Employer or his representative
(16) -139- FORM - XIX [ See rule 241(1)(b) ] Register of Deductions for Damage or Loss Name and Address of establishment where building or other construction work is carried on/is to be carried on Nature of building or other construction work Name and permanent address of building workers Name and permanent address of the employer Sl.
No.
Name of work Father's/ Husband's name Designation/ nature of employment Particulars of damage or loss Date of damage or loss Whether building worker showed Cause against deduction Name of person in whose presence building worker's explanation was heard Amount of deduction imposed Number of instalments Date of recovery First instalment Last instalment
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) 140- FORM - XX [See rule 241 (1) (b) ] Register of Fines Name and address of establishment Name and permanent address of where building or establishment other construction work is carried on/is to be carried on Nature of building or other Name and address of the employer construction work Sl.
No.
Name of building worker Father's/ Husband's name Designation/ nature of employment Act/ omission for which fine imposed Date of offence Whether building worker showed cause against fine Name of person in whose presence building worker's explanation was heard Wage periods and wages payable Amount of the fine imposed Date on which fine realised Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) -141- FORM - XXI [See rule 241 (1) (b) ] Register of Advances Name and address of establishment Name and permanent address of where building or other construction establishment work is carried on/is to be carried on Nature of building or other construction Name and address of the employer Sl.
No.
Name Father's/ Husband's name Nature of employment/ designation Wage period and wages payable Date and amount of advance given Purpose(s) for which advance given Number of instalments by which advance to be repaid Date and amount of each instalment repaid Date on which last installment was repaid Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) -142- FORM - XXII [See rule 241(1)(c)] Register of Overtime Name and address of establishment Name and permanent address of where building or other construction establishment work is carried on/is to be carried on Sl.
No.
Name of the building worker Father's/ Husband's name Sex Designation/ Nature of employment Date on which overtime worked Total overtime worked or production in case of piece rated Normal rates of wages Overtime rate of wages Overtime earnings Date on which overtime wages paid Remarks
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) -143- FORM - XXIII [See rule 241 (2) (a) ] Wage Book Name and Address of Employer Name and permanent address of establishment Name and address of the establishment Nature of building or other where buiding or other construction work construction work carried on For the Week/Fortnight/ Month ending ………………….
1. Number of days worked……………………….
2. Number of units worked in case of piece-rate & workers………………….
3. Rate of daily/monthly wages/piece-rate……………………………
4. Amount of overtime wages…………………………………………
5. Gross wages payable……………………………………………….
6. Deductions, if any, on account of the following:-
(a) fines
(b) damage or loss
(c) loans and advances
(d) subscription towards provident fund
(e) subscription towards the Building Workers Welfare fund
(f) any other deductions e.g. subscriptions to Co-operative society or account of loans from Co-operative society/housing loan, or contribution to any relief fund as per provision of Clause (P) of sub-section (2) of section 7 of the Payment of Wages Act or for payment of any premium of Life Insurance Corporation.
7. Net amount of wages paid………………………………………… Initials of the employer or his Representative -144- FORM - XXIV [See rule 241(2) (b)] Service Certificate.
Name and permanent address of Name and address/location the establishment where the building or other construction work carried on/ to be carried on Nature and location of work…………………………..
Name and address of the workman…………………… Age Date of Birth ……………………………………..
Identification Marks …………………………………..
Father's/Husbands name ……………………………… Total period for which employed Sl.
No.
From To Nature of work done Rate of wages (with Particulars of unit in case of piece work) If the building worker was a beneficiary his registration number, date and the name of the Board Reasons/grounds on which the employment terminated Remarks
(1) (2) (3) (4) (5) (6) (7) (8) Signature -145- FORM XXV.
(See rule 242) COMBINED ANNUAL RETURN OF EMPLOYER TO BE SENT TO THE REGISTERING OFFICER Year ending 31st December ………….
1. Full name and full address of the establishment of the building and other construction work (Place, Post Office, District)
2. Name and permanent address of the establishment
3. Name and address of the employer
4. Nature of building and other construction work carried on
5. Full name of the Manager or person responsible for supervision and control of the establishment
6. Number of building workers ordinarily employed
7. Total number of days during the year on which building workers were employed
8. Total number of man-days worked by building workers during the year
9. Maximum number of building workers employed on any day during the year
10. The number of accident that took place during the year as under:
(a) The total number of accidents.
(b) The number of accidents resulting in disablement of building workers for less than 48 hours, the number of building workers involved and the number of man-days lost.
(c) The number of accidents resulting in disablement of building workers beyond 48 hours but not resulting in any permanent partial or permanent total disablement, the number of building workers involved, and the number of man-days lost on account of such accidents.
(d) The number of accidents resulting in permanent partial or total disablement, the number of building workers involved and the number of man–days lost on account of such accidents.
(e) The number of accidents resulting in death of building workers and the number of resultant deaths.
The Chief Inspector or Inspectors appointed by the Government under the Act shall direct the owners of establishments registered under this Act, to send the copies of Annual Returns submitted by the employers of registered establishments in respect of the Government to the Chief Inspectors of Building and Other Construction Work of Inspections by virtue of provisions of Section 60 of the Act.
officers Typewritten text [ officers Typewritten text 1 Subs. by G.O. Ms.No.148, Labour and Employment, dated the 31st August, 2017.
officers Typewritten text ________________________________________________________________________________________________ officers Typewritten text 1 -146- The Chief Inspector or Inspectors appointed under this Act by the Government shall direct the owners of such establishments as are registered under this Act by registering officers appointed by the Government to send copies of the Annual Returns to the Director General by virtue of provisions of Section 60 of the Act.
11. Change, if any, in the management of the establishment, its location, or any other particulars furnished to the Registering Officer in the application for Registration indicating also the dates.
12. (i) Particulars of Maternity Benefits:
Number of Employees received Total amount paid Miscarriage Confinement Illness Medical Bonus Total
(ii) Number of women who gave notice under Section 6 of the Maternity Benefit Act, 1961:
(iii) Number of women who were granted permission to absent on receipt of notice of confine- ment:
(iv) Claims for maternity benefit rejected: Number Amount not paid
(v) Claims for medical bonus rejected: Number Amount not paid
(vi) Cases in which leave for miscarriage was applied for but was rejected:
Number Amount not paid
(vii) Cases in which additional leave for illness under Section 10 was applied for but was rejected:
Number Amount not paid
(viii) Cases in which payment was made to persons other the woman concerned:
Number Amount paid
(ix) Women deprived of maternity benefit and/ or medical bonus under proviso to sub-section (2) of Section 12 of the Maternity Benefit Act, 1961:
Number Amount not paid
(x) Cases in which payment was made on the order of the Appellate Authority or Inspector:
Number Amount paid
(xi) Number of cases where prenatal confinement and postnatal care was pro- vided by the management free of charge under Section 8 of the Maternity Benefit Act, 1961:
13. (i) Particulars of Deductions made from Salary in respect of persons whose wages are not more than the wages specified by Central Government under sub-section (6) of Section 1 of the Payment of Wages Act, 1936 (Central Act 4 of 1936) :- Number of employees involved Total Amount of deductions made Fines Damages/ Loss Breach of Contract Others Total
(ii) Details of number of persons earning not more than the wages specified by Central Government under section 6 of the Payment of Wages Act, 1936 (Central Act 4 of 1936) :- Men:
Women:
Adolescent:
-147-
(iii) Details of money value concession paid (in Rupees):
(iv) Total wages including deductions under sub-section (2) of Section 7 of the Payment of Wages Act, 1936 (Central Act 4 of 1936):- Basic Wage.
Dearness Allowanc es.
Over time.
Non Profit sharing bonus.
Other allowances in cash.
Arrears of pay in re- spect of previous year paid during the year.
Total.
(v) Details of the remittances of Fines collected towards Tamil Nadu Labour Welfare Fund.
Demand Draft No.
Date. Bank. Amount Rs.ps.
1st Quarter 2nd Quarter 3rd Quarter 4th Quarter
(vi) Total cash value of the wages paid in kind:
14. Payment of Bonus paid for the accounting year:
Number of em- ployees eligible for Bonus.
Percentage of Bonus declared.
Total amount of Bonus paid.
Date of payment.
15. Contract Labour:
Names and addresses of con- tractors.
Period of contract.
Nature of work.
Number of days worked.
Number of man days worked.
Maximum num- ber of workers employed by each contractor.
16. Inter-state Migrant Workmen:
Name and address of contractors Period of contract Nature of work Maximum number of migrant workmen employed by each contractor Number of days worked Number of man-days worked Place…………….. Employer………….
Date……………… officers Typewritten text ] officers Typewritten text -148- FORM - XXVI [ See rule 74(b) ] Register of Periodical Test/Examination of Lifting Appliance And Gears Etc.
PART-1 Initial and periodical load test of lifting appliances and their annual thorough examination.
"Thorough Examination" means a visual examination, supplemented, if necessary, by other means such as a hammer test, carried out as carefully as the conditions permit, in order to arrive at a reliable conclusion as to the safety of the parts examined, and if necessary, for such examination parts of the lifting appliances and gear shall be dismantled.
(A) Initial and periodical load tests of lifting appliance Situation and description of lifting appliances tested with distinguishing number of marks if any.
Number of certificate of test and examination of competent person.
I certify that on the date on which I have appended by signature the lifting appliance shown in column (1) was tested and no defects affecting its safe working condition were found other than those shown in column (5) Remarks (to be signed and dated) Date and signature with seal Date and signature with seal
(1) (2) (3) (4) (5)
1.
2.
-149- (B) Annual thorough examination.
I certify that on the date to which I have appended my signature, the lifting appliance shown in column(1) was thoroughly examined and no defects affecting its safe working conditions were found other than those shown in column(12).
Date and Signature with seal Date and Signature with seal Date and Signature with seal Date and Signature with seal Date and Signature with seal Date and Signature with seal Ramarks (to be signed and dated)
(6) (7) (8) (9) (10) (11) (12)
1.
2.
Explanation:- If all the lifting appliances are thoroughly examined on the same date it will be sufficient to enter in column (1) "All lifting appliances", If not, the parts which have been thoroughly examined on the dates must be clearly indicated.
PART-II Initial and periodical load test of loose gears and annual thorough examination List of loose gear:
The following classes of loose gears namely-
1. Chains made of malleable cast iron;
2. Plate link chains;
3. Chains, rings, hooks, shackles and swivels made of steel;
4. Pitched chains;
5. Rings, hooks, shackles and swivels permanently attached to pitched chains, pulley blocks, container, spreaders, trays, slings, baskets, etc., and any other similar gear;
6. Hooks and swivels having screw-threaded parts or ball bearings or other case-heardened parts; and
7. Bordeaux connections.
-150- Initial Test and periodical load test of loose gears.
Distinguishing Number or marks Description of loose gear tested and examined Number of certificates of test and examination of competent person I certify that on the date to which I have appended my signature the loose gears shown in column (1) and (2) were tested and no defects affecting the safe working condition were found other than those shown in column (6) Date and signature with seal Date and signature with seal
(1) (2) (3) (4) (5)
1.
2.
3.
4.
5.
Annual thorough examination of loose gears.
Remarks (to be signed and dated) I certify that on the date to which I have appended my signature the loose gears shown in column(1) and (2) were thoroughly examined by me and no defects affecting their safe working condition were found other than those shown in column(10).
Remarks (to be signed and dated) Date and signature with seal Date and signature with seal Date and signature with seal
(6) (7) (8) (9) (10)
1.
2.
3.
4.
5.
-151-
PART-III Annealing of Chains, Rings, Hooks, Shackles and Swivels (other than those exempted.)
(See Part-II)
12.5 mm and smaller chains, rings, hooks, shackels and swivels in general use, Other chains, rings, hooks, Shackles and swivels in General use.
If used with lifting appliance driven by power, must be annealed once atleast in every six months if used solely with lifting appliance worked by hand must be annealed once atleast in every twelve months.
If used with lifting appliance driven by power, must be annealed once atleast in twelve months. If used solely with lifting appliance worked by hand, must be annealed once atleast in every two years.
Explanation:- It is recommended though not required by rules that annealing should be carried out in a suitably constructed furnace heated to temperature between 1100 degree and 1300 degree Fahrenheit or 600 degree and 700 degree Centigrade, for a period between 30 and 60 minutes.
Distinguishing Description Number of I certify that on the date to Remarks Number or of the which I have appended (to be mark gear certificate my signature, the gear described signed annealed of test and in columns 1 and 2 was and examination effectually annealed under dated) my supervision; that after being so annealed every article was carefully inspected and that no defects affecting its safe working condition were found other than those shown in column 7.
Date and Date and Date and signature signature signature with seal with seal with seal
(1) (2) (3) (4) (5) (6) (7) officers Typewritten text ] Preliminary.
Responsibilities and duties of employers, architects, project engineers and designers, building workers, etc.
State Advisory Committee, Registration of Establishments.
Registration of Establishments.
CHAPTER V.
PART-111.
Slipping, tripping, cutting, drowning and falling hazards.- Use of Safety Helmets and Shoes:-- Lifting Appliances And Gear.
Runways and Ramps.
Work on or adjacent to water.
CHAPTER X.
Concrete work Preparation and pouring of concrete and erection of concrete structures,—The Demolition.
Excavation and Tunneling Works.
CHAPTER XIV.
Ladders and Step-Ladders.
CHAPTER XVI.
Structural Frame and Form Work.
Stacking and Unstacking.
Scaffold.
Cofferdams and Caissons.
CHAPTER XXI
CHAPTER XXII,
CHAPTER XXIII
CHAPTER XXIV.
CHAPTER XXV.
PART IV .
Weekly rest, payment for work done on the day of rest at overtime rate, etc.- Application of provisions of this chapter to certain classes of building workers,-
CHAPTER XXVII
CHAPTER - XXVIII
CHAPTER XXIX.
PARTY.
Schedule-I TABLE TABLE TABLE TABLE Procedure for testing:
The derricks tested under clause (3) shall not be used in union purchase rigs unless,-
SCHEDULE-II.
SCHEDULE-IlI SCHEDUI.E - IV
SCHEDULE - V.
SCHEDULE-VI .
SCHEDULE-VII.
SCHEDULE-VIII Appointment of Safety Officers.
SCHEDULE -IX Hazardous process.
SCHEDULE-X.
SCHEDULE-XI
SCHEDULE-XII.
PERMISSIBLE LEVELS OF CERTAIN CHEMICAL SUBSTANCES IN THE WORK ENVIRONMENT Declaration by the employer- FORM - III Notice of commencement/Completion of Building or other construction work.
FORM-VII.
FORM - VIII FORM - IX FORM - X Certificate of Annual Thorough examination of loose Gears Exempted from Annealing.
CERTIFICATE OF MEDICAL EXAMINATION Health Register Notice of poisoning or notifiable occupational diseases.
Report of Accidents and Dangerous Occurrences.
Register of Building and other Constructions Workers employed by the Employer.
FORM-XVI Muster Roll FORM - XVII Register of Wages Name and address of the establishment FORM - XIX Register of Deductions for Damage or Loss Register of Fines FORM - XXI Register of Advances FORM - XXII Register of Overtime FORM - XXIII Wage Book FORM - XXIV Service Certificate.
FORM - XXVI
PART-1 (A) (B)
PART-II
PART-III