Uttar Pradesh Legal Metrology(Enforce… Bare Act

The source publishes this enactment as a single document rather than provision by provision, so the whole text is below and there are no per-section pages for it. Nothing has been shortened.

Type	Rules
Year	2010
Jurisdiction	State of Uttar Pradesh
Status	In force as published by the source
Text	Published as one document, as the source published it
Subjects	consumer

mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 1 In pursuance of the provisions of clause (3)of article 348 of the constitution, the Governor is pleased to order the publication of the following English translation of the Notification No- 331/LXXXIV-1-2011-23 Ba Ma-2010, dated 1 April, 2011: No.- 331/LXXXIV-1-2011-23 Ba Ma-2010 Lucknow, Dated April 1, 2011 In exercise of the powers under sub-section (1) of Section 53 of the Legal Metrology Act, 2009 ( Act No 1 of 2010 ), the Governor after consultation with the Central Government is pleased to make the following rules, the same having been previously published in the Gazette under Government Notification No-216/84-1-2011-23 Ba Ma/2010, dated February 24, 2011, as required by sub-section (4) of Section 53 of the said Act. UTTAR PRADESH LEGAL METROLOGY(ENFORCEMENT) RULES 2011 Short title 1-(1) These rules may be called the Uttar Pradesh Legal Metrology (Enforcement) and comm- Rules, 2011. encement

(2) They shall extend to the Whole of Uttar Pradesh

(3) They shall come into force with effect from the date of their publication in Gazatte. Definitions 2 – In these rules, unless the context otherwise requires –

(a) “Act” means the Legal Metrology Act, 2009;

(b) “Reference Standard Laboratory” means a laboratory set up by the Central Government under the Act, where Reference Standards, Secondary Standards and Working Standards are maintained:

(d) Words and expressions used in these rules and not defined but defined in the Act shall have the meaning respectively assigned to them in the Act. Reference 3-The reference Standards shall be kept at such place, in such manner and in such Standards custody as may be prescribed under the Legal Metrology (National Standards) Rules, 2011. Secondary 4- (1) Every secondary Standards shall be verified at any of the Reference Standards Standards Laboratories, in such manner and at such periodical intervals as may be prescribed under the rules and shall, if found on such verification to conform to the Standards established by or under the Act, be stamped by the Reference Standard Laboratory or a certificate of verification will be issued by the laboratory.

(2) The Secondary Standards shall be kept at such place, and in such custody as the controller may direct. Working 5. (1) Every Working Standards shall be verified either at any of the Reference Standards Standards laboratories or at any of the Secondary Standards Laboratories maintained by the State Government, in such manner and at such periodical Intervals as may be prescribed under the rules and shall, if found on such verification to conform to the Standards established by or under the Act, be stamped or certificate of verification will be issued by that laboratory as the case may be. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 2

(2) The verified Working Standards shall be kept in the custody of legal metrology officer. Secondary 6. (1) A set of secondary standard balances shall be maintained at every place Standards where the Secondary Standard Weights are kept. balances

(2) The number, types and specifications of such balances shall be such as may be prescribed under the Legal Metrology (General) Rules, 2011.

(3) Every Secondary Standards balance shall be verified at least once within a period of twelve months and shall be adjusted, if necessary, to make it correct within the limits of sensitivity and other metrological qualities prescribed under the Act, by the Reference Standards Laboratory or by the Controller or such other officer as may be authorized by the Controller in this behalf. Working 7. (1) A set of working standard balances shall be maintained at every place where Standard Working Standard Weights are kept. Balances

(2) The number, types and specifications of such balances shall be such as may be prescribed under the Legal Metrology (General) Rules, 2011.

(3) Every Working Standards balances shall be verified at least once within a period of twelve months and shall be adjusted, if necessary, to make it correct within the limits of sensitivity and other metrological qualities prescribed under the Legal Metrology (General ) Rules, 2011, by the Reference Standards Laboratory or at any of the place where Secondary Standards are maintained by the State Government. Physical 8. Every Weight or Measure used or intended to be used in any transaction or for Characteris- protection shall conform as regards physical characteristics, configuration, tics,configu- constructional details, materials, performance, tolerances and such other details, ration, const- to the specifications prescribed under the Act or the Legal Metrology ( General). ructional Rules, 2011 details of Weights and Measures . Use of Bull- 9. (1) No Weights other than a Bullion Weight, as specified in Legal Metrology ion Weights, (General) Rules 2011, shall be used in any transaction or protection in bullion Carat Weig- including precious metals, pearls, ornaments or other articles made of gold or silver. hts etc

(2) No weight other than a carat weight shall be used in any transaction in precious stones,

(3) Only beam scale of class A or class B category or a non automatic weighing instrument of high accuracy class (class II) or special accuracy class (class-I) shall be used in any transaction or protection referred to in sub-rules (1) and (2). Use of weights- 10. Except in the cases of commodities specified in Schedule I, the declaration only or meas- of quantity in every transaction, dealing or contract, or for protection shall be in ures only or the terms of the unit ofnumber in mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 3 certain cases.- (a) Weight, if the commodity is solid, semi-solid, viscous or a mixture of solid and liquid;

(b)Length ,if the commodity is sold by linear measure;

(d) Volume, if the commodity is liquid or is sold by cubic measure; or

(e) Number, if the commodity is sold by number. Licensing of- 11(l)Every manufacturer or repairer of, or dealer in, weight or measure shall Manufacturer, make an application for the issue of a licence to the Controller legal metrology repairer and or such other officer as may be authorized by him in this behalf, in the appropriate dealer of form set out in Schedule II-A. Weights and Measures – Provided that no licence to repair shall be required by a manufacturer to repair weight or measure manufactured by him and used in a state other than the state of manufacture of the same, but the manufacturer has to inform in advance the concerned legal metrology officer about the repairing.

Provided that a person who bonafide repairs any weight or measure owned or possessed by him shall not require a repairer license.

(2) Every manufacturer or repairer, or dealer in weight or measure shall make an application for the renewal of a licence thirty days before the expiry of validity of the licence to the Controller legal metrology or such other officer as may be authorized by him in this behalf, in the appropriate form set out in Schedule II-B.

(3) Every licence issued to a manufacturer, repairer or dealer shall be in the appropriate form set out in Schedule III.

(4)1 [ Every licence issued to a manufacturer, repairer, or dealer shall be valid for a minimum period of one to ten calendar years and may be renewed for a period of one to ten calendar years, by the Controller or such other officer as may be authorized by him in this behalf on payment of necessary fee as specified in the Schedule IV ].

(5) The fee payable for the alteration of a license or for the issue of a duplicate license shall be as specified in Schedule IV.

Provided that an additional fee at full rate specified in Schedule IV shall be payable by the applicant if he is permitted by the, Controller legal metrology or such other officer as may be authorized by him in this behalf to make an application for the renewal of a license within a period of three months from the date of expiry of the licence.

(6) The Controller or such other officer as may be authorized by him in this behalf shall maintain a register of licensed manufacturers, dealers and repairer in the form set out in Schedule V.

(7) Every manufacture/repairer/dealer licensed under the Act and these rules shall maintain such workshop/equipments/tools/registers etc. as the case may be, as per the terms and conditions of the licence.

(8) Every repairer licensed under the Act and these rules shall furnish a security deposit for each licence to the State Government as specified in Schedule VI.

(9) Every licence issued or renewed under this act shall be displayed in a conspicuous place in the premises where the licencee carries on business. 1 [Substituted vide Gazette Notification No. 456/LXXXIV-1-2013-23 Ba.Ma.-2010 dated 11th September, 2013] mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 4

(10) A licence issued or renewed under this act shall neither be saleable nor transferable. Suspension- 12(1) The Controller or such other officer as may be authorized by him on his and cancell- behalf may, if he has any reasonable cause to believe that the holder of any ation of licence issued, renewed or continued under this Act has made any statement licence in, or in relation to, any application for the issue, renewal or continuance of the granted: licence,which is incorrect or false in any material particular or has contravened any provision of the Act or any rule or order made there under, suspend such licence, pending the completion of any inquiry against the holder of such licence;

Provided that no such licence shall be suspended unless the holder thereof has been given a reasonable opportunity of showing cause against the proposed action:

Provided further that where the enquiry referred to in this sub-rule is not completed within a period of three months from the date of suspension of a license, such suspension shall, on the expiry of the period aforesaid, stand vacated.

(2) The Controller or such other officer as may be authorized by him on his behalf may, if he is satisfied, after making such inquiry as he may think fit, that the holder of a licence has made a false or incorrect statement of the nature referred to in sub- section (1), or has contravened any law or order referred to in that sub-rule, cancel such licence:

Provided that no such licence shall be cancelled unless the holder thereof has been given a reasonable opportunity of showing cause against the proposed section.

(3) Every person whose license has been suspended shall, immediately after such suspension, stop functioning as such licencee and shall not resume business as such licencee until the order of such suspension has been, or stands, vacated.

(4) Every licencee whose license has been suspended or cancelled shall, after such suspension or cancellation, as the case may be, surrender such licence to the authority by which such licence was issued.

(5) Every licencee whose licence has been cancelled shall, within a period of thirty days from the date of such cancellation, or within such further period, not exceeding three months from such date, as the Controller or such other officer as may be authorized by him on his behalf may, on sufficient cause , being shown allow,dispose of the weights or measures which were in his possession, custody or control on the date of such cancellation and in the event of his failure to do so, the Controller or any other officer authorized by him, in writing, in this behalf, may seize and dispose of the same and distribute the proceeds thereof in such manner as may be prescribed Records to- 13 . Every manufacturer or repairer of, or dealer in weight or measure licensed be mainta- under the Act and these rules shall maintain records and registers in the appropriate ined by form set out in Schedule-VII and also submit such periodical reports/returns as manufac- may be specified. turers etc. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 5 Periodical 14 Periodical interval for the verification of weights or measures shall be interval for as specified in Legal Metrology (General) Rules 2011. the verification of weights or measures- Verification- 15 (1) Every person using any weight or measure in any transaction or for and inspe- protection shall present such weight or measure for verification / re-verification at ction of the office of the Legal Metrology Officer, or at such other place as the Legal weights or Metrology Officer may specify in this behalf, on or before the date on which the measures verification falls due; ;

Provided that where any weight or measure is such that it cannot, or should not be moved from its location, the person using such weight or measure shall report to the Legal Metrology Officer at least thirty days in advance of the date on which the verification falls due.

(2) Where any weight or measure is such that it cannot, or should not, be moved from it’s location, Legal Metrology Officer shall take necessary steps for the verification of such weight or measure at the place of its location.

(3) For the verification of weight or measure referred to in sub-rule (2) the user shall provide such facilities as may be specified by the Controller.

(4) Every weight or measure presented for verification shall be complete in itself.

(5)Every weight or measure shall be verified in clean condition, and if necessary, the Legal Metrology Officer shall require the owner or user to make necessary arrangement for the purpose.

(6) A Legal Metrology Officer shall visit, as frequently as possible during the period specified in rule 14, every premises within the local limits of his jurisdiction to inspect and test any weight or measure which is being, or is intended or is likely to be used in any transaction or for protection.

(7)The Legal Metrology Officer shall obliterate the stamp on any weight or measure if it is found during inspection that -

(a) Any weight or measure which being due for re-verification has not been submitted for such re-verification.

(b)Any weight or measure which does not conform to the Standards established by or under the Act .

Provided that where the Legal Metrology Officer is of the opinion that the defect or error in such weight or measure is not such as to require immediate obliteration of the stamp, he shall inform the user, of the defect or error found in the weight or measure and call upon user to remove the defect or error within such time, not exceeding eight days and shall-

(1) if user fails to remove the defect or error within that period, obliterate the stamp, or mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 6

(ii) if the defect or error is so removed as to make the weight or measure to conform to the Standards established by or under the Act, verify and stamp such weight or measure.

Explanation: The obliteration of the stamp on any weight or measure shall not take away or abridge the power of the Legal Metrology Officer to seize such weight or measure in accordance with the provisions of the Act. Stamping - 16(1) The Legal Metrology Officer shall stamp every weight or measure, if after of weights testing and verification, he is satisfied that such weight or measure conforms to or measures the Standards established by or under the Act, with a stamp of uniform design, issue by the Controller, which shall indicate the number allotted for administrative purpose to the Legal Metrology Officer by whom it is stamped.

Provided that if, by reason of the size or nature of any weight or measure, it is not desirable or practicable to put a stamp thereon, the Legal Metrology Officer shall take such action as may be directed by the Controller by a general or a special order in writing.

(2) Legal Metrology Officer shall also mark the year and its quarter of stamping on every verified weight or measure except when the size or nature of such weight or measure makes it impracticable.

Explanation – A year shall be deemed to consist of four quarters of which first Quarter shall be of the months of January, February and March which shall be marked as A; second quarter shall be of the months of April, May and June which shall be marked as B; third quarter shall be of the month of July, August and September which shall be marked as C and fourth quarter shall be of the months of October, November and December which shall be marked as D

(3)on completion of verification and stamping the Legal Metrology Officer shall issue a certificate of verification in the form set out in schedule VIII.

(4)Where certificate of verification is lost or destroyed, the holder of the certificate of verification shall forthwith apply to the Legal Metrology Officer who had issued the certificate, for the issue of a duplicate certificate of verification. Every such application for the issue of a duplicate certificate shall be accompanied by a fee of rupees ten.

(5) On receipt of an application under sub-rule (4), the Legal Metrology Officer shall issue to the applicant a duplicate copy of the certificate of verification marked “DUPLICATE’ Fee for 17. (1) Fees payable for verification and stamping of weight or measure at the verification office or camp office of the Legal Metrology Officer shall be as specified in Schedule-IX.

(2) If, at the request of the user of weight or measure, verification is done at any premises other than the office or camp office of the Legal Metrology Officer, an additional fee shall be charged at half the rate specified in the Schedule-IX and the user of the weight or measure shall pay the expenses incurred by the Legal mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 7 Metrology Officer for visiting the premises including the cost of transporting and handling the Working Standard and other equipment subject to a minimum of rupees one hundred.

Provided that no additional fee shall be charged for verification and stamping, in situ, of,-

(i)Vehicle tanks for petroleum products and other liquids, Meter for Liquids other than water (Fuel Dispenser, Liquid Petroleum Gas, ,Milk Dispensers), Compressed Natural Gas Dispensers, Non-automatic Weighing Instruments like weighbridges, platform machines, crane scale, Automatic Gravimetric Filling Instruments, Automatic Rail- weighbridge, Discontinuous Totalizing Automatic Weighing Instruments, and such other weight or measure which cannot, and should not be moved form its location;

(ii) Weight or measure in the premises of manufacturer or dealer of such weight or measure.

(3) If a weight or measure is presented to the Legal Metrology Officer for re-verification after expiry of the validity of the stamp, an additional fee at half the rate specified in Schedule-IX shall be payable for every quarter of the year or part thereof.

(4) No fee shall be payable for re-stamping any weight or measure held in stock with manufacturer or dealer within the period specified in rule 14 from the date on which it was last stamped, provided that the original stamp was not obliterated.

(5) A weight or measure which on verification/ inspection is found to be incorrect shall be returned to the person concerned for adjustment informing him, in a proforma specified by the Controller, of the defects found in the weight or measure, and calling upon him to remove the defects within a period not exceeding seven days. When the necessary adjustment has been carried out, such weight or measure shall be verified on payment of the fees specified in schedule IX and if found correct shall be stamped. Collection 18.(1) Before commencing the work of verification or re-verification, the Legal of fees and Metrology Officer shall inform the person concerned of the fees payable by him deposit and shall receive the same in the manner as authorized by the Controller and issue into the a receipt on the form approved by the Controller, one copy of such receipt being Treasury kept on record.

Provided that fees payable by a department of the Central or State Government under these rules may be realized in such manner as may be directed by the Controller.

(2) The Legal Metrology Officer shall maintain a register, in the form approved by the Controller, which shall be written up from day-to-day and shall show the amount of fees and other charges collected during the day.

(3) All payment received by the Legal Metrology Officer during the week shall mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 8 be paid into the Government Treasury under the appropriate “Head of Account” on such dates or days as may be specified by the Controller from time to time, and a receipt thereof be obtained and an intimation to that effect be sent to the Controller or other officer authorized by him in this behalf. Disposal of 19. (1) Any un-verified weight or measure shall be returned to the person from seized weights, whom such weight or measure was seized if that person gets the same verified and measures, etc. stamped, within fifteen days of the seizure, on payment of the prescribed fee including the additional fee payable for undertaking re- verification after the expiry of the validity of the stamp.

(2) Any weight or measure or documents or thing or goods seized and detained under section 15 of the Act, which is to be the subject of proceedings in a court shall be produced by the Legal Metrology Officer before the court and shall, after conclusion of the proceedings, be taken possession of by the Legal Metrology Officer and dealt with in accordance with the orders of the court:

Provided that in the absence of the order of the court, weight or measure or document or thing or goods shall be dealt with as the Controller may by special order direct and the material thereof shall be sold and the proceeds credited to the Government.

(3) If any goods seized under section 15 of the Act, are subject to speedy or natural decay, the Legal Metrology Officer shall have the goods weighed or measured on a verified weighing or measuring instrument available with him or nearest the place of offence and enter the actual weight or measure of the goods in a form specified by the Controller for this purpose, and shall obtain the signature of the trader or his agent or such other person who has committed the offence the goods in question shall be returned to the trader or the purchaser as the case may be:

Provided that if the trader or his agent or the other person (who has committed the offence) refuses to sign the form, the Legal Metrology Officer shall obtain the signature of not less then two persons present at the time of such refusal by the trader or his agent or other person. In the case of goods returned to the traders , the trader shall give an undertaking that he shall not sell the defective goods without rectifying the defects thereon.

(4) Where the goods seized under sub-section (1) of section 15 of the Act are contained in a package and the package is false or does not conform to the Provisions of the Act, or any rules made there under, and the goods in such package are subject to speedy or natural decay, the Legal Metrology Officer as far as may be, may dispose of the goods in such package in accordance with the provisions of sub-rule (3):

Provided that the Controller shall be the final authority to decide whether the goods seized and detained are subject to speedy or natural decay. .

(5) Where the goods seized under sub-section (1) of section 15 of the Act are not subject to speedy or natural decay, the Legal Metrology Officer may retain the package for the purpose of prosecution under this Act after giving the trader or his mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 9 agent or the other person (who has committed the offence) a notice of such seizure

(6) The goods referred under sub-rule(4) & (5) which are not to be the subject of proceedings in a court, shall after the expiry of sixty days of its seizure, be so dealt with as the Controller may by special order direct. Validity of 20.(1) A weight or measure which is, or is deemed to be, duly verified and weights or stamped under this rule shall be deemed to conform to the standards established measures by or under the Act at every place within the State in which it is stamped unless it is duly stamped found on inspection or verification that such weight or measure has ceased to conform to the standards established by or under the Act.

(2) No weight or measure which is, or is deemed to be, duly verified and stamped under this Act shall require to be re-stamped merely by reason of the fact that it is being used at any place within the state other then the place at which it was originally verified and stamped:

Provided that where a verified weight or measure, installed at one place is dismantled and re-installed at a different place, such weight or measure shall not be put into use unless it has been duly re-verified and stamped, notwithstanding that periodical re-verification or such weight or measure has not become due.

(3) Where a verified weight or measure has been repaired, whether by a licensed repairer or by the person owning and possessing the same, such weight or measure shall not be put into use unless it has been duly re-verified and stamped, notwithstanding that periodical re-verification of such weight or measurer has not become due. Qualifications 21. The qualifications of the Legal Metrology Officer shall be as specified in of Legal Met- Legal Metrology (General) Rules 2011. rology Officer Provision 22. (1 )Every Legal Metrology Officer shall be provided with Working/ of supply Secondary Standard weights, Working/ Secondary Standard balances, and Working such other equipments including weighing and measuring devices as may be /Secondary approved by the Controller from time to time. Standards Equipment,. (2) Legal Metrology Officer shall be provided with such dies, punches, etc. to the paper seal / sticker and such other equipments as may be necessary for affixing Legal Metr- the verification stamp, the design and number of which are to be approved by Ology Officer the Controller.

(3) Every Legal Metrology Officer shall be provided with punches of suitable sizes of eight-pointed star as shown below for obliterating stampsmÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 10 Provisions 23. (1) Every person using a beam scale in any transactions in his premises shall relating to suspend the same to a stand or to a chain by a hook : use of weight, measure, etc Provided that this sub-rule shall not apply to itinerant vendors.

(2) Every weight or measure shall be used in a clean condition and in proper : lighting arrangement.

(3)Any weight or measure which has been verified and stamped in situ, shall not be dismantled and removed from it original site without prior intimation to the concerned Legal Metrology officer.

(4) To ensure a proper check of the accuracy of a weighing instrument the user shall keep at the site of each weighing instrument duly verified and stamped weights equal to one-tenth of the capacity of the instrument, or One tonne, whichever is less, and consumer can check the accuracy of the weighing instrument:

Provided that the Controller may specify the total number of verified and stamped weights to be maintained in trade premises where the number of weighing instruments are more than one.

(5) To ensure proper delivery from petrol/diesel pumps, the retail dealer of the Pump shall keep a verified 5 litre/10 litre capacity measure in his premises and check the output from the pump every day to ensure its correct delivery. In case of any short delivery, the dealer shall stop the delivery through the Pump immediately and inform the concerned Legal Metrology Officer to recalibrate the pump. Certificate of 24 . The person whom a certificate of verification is issued shall exhibit the same verification to in a conspicuous place in the premises where the weights, measure or weighing be exhibited or measuring instruments to which the certificate relates are used;

Provided that in the case of itinerant vendor, the certificate shall be kept with the person:

Provided further that in the case of vehicle tank, the certificate of verification shall be kept with the vehicle. Penalty for 25 Whoever contraventions any provision of these rules, for the contraventions Contravention of which no punishment has been separately provided in the Act, shall be punished of rules with fine, which may extend to five thousand rupees. Wherever the rules are in . conflict with provisions of the Act, the Act will prevail upon the rules. Form of 26. (1) Every appeal under the Act and these rules shall be preferred in the appeal form set out in schedule X and shall be accompanied by a copy of the order appealed against. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 11

(2) An application for appeal to State Government shall be accompanied by fee of Rs.500 and for appeal to controller shall be accompanied by fee of Rs.200 paid either by cash or by affixing court fee stamp for said value, as the case may be. Fee for compou- 27. The fee for compounding of offences committed under the Act shall be as nding of offences. prescribed in the schedule-XI.

SCHEDULE-1 (See Rule 10) Exceptions referred to in Rule 10 1- The following commodities may be sold by weight, measure or number as shown against the commodity. TABLE ------------------------------------------------------------------------------------------------------------------------ Sr. No. Commodity Whether declaration to be expressed in terms of weight, Measure or number or two or more of them. ------------------------------------------------------------------------------------------------------------------------

(1) (2) (3) ------------------------------------------------------------------------------------------------------------------------ 1- Aerosol products weight 2- Acids in liquid form weight or volume 3- Compressed or liquefied weight and equivalent volume at stated Gas (but not liquefied temperature and pressure Petroleum gas) 4- Butter (Incl. peanut butter), weight Cheese, curd, ghee 5- Electric cables length or weight 6- Electric wire length or weight 7- Fencing wire length or weight 8- Hair oil, un perfumed weight or volume 9- Fruits and vegetables number or weight 10- Furnace oil weight or volume 11- Linseed oil and other weight or volume Vegetable oils 12- Heavy residual fuel oil weight 13- Industrial diesel fuel volume 14- Honey, malt extract, golden weight Syrup treacle 15- Ice cream and other similar weight or volume Frozen treacle 16- Liquid chemicals weight or volume 17- Liquid petroleum gas weight 18- Nails, wood screws number or weight 19- Paint (other than paste paints volume Or solid paint), varnish and Varnish stairs, enamels 20- Papad number and weight 21- Paste paint, sold paint weight mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 12 12 22- Rassgulla, Gulabjamun and other weight Sweet prepration 23- Ready made garments number and size 24- Sauce, all kinds weight 25- Tyres and tubes number 26- Yarn weight or length of yarn ------------------------------------------------------------------------------------------------------------------------ SHEDULE- II “A” [ See rule 11 (1)] From- LM-1 To, [ Application from for licence as manufacturer of weights & measures under the Legal Metrology Act, 2009] Sr No. To be filled by the Comments of the Applicant inspection officer

(1) (2) (3)

1. Name of the manufacturing concern for which licence --------------------- is desired.

2. Complete address of the concern. Whether premises --------------------- are owned/rented/taken on lease duly supported by documents.

3. Date of establishment of workshop/factory. ---------------------

4. Name (s) and address (s) along with their father’s/ --------------------- husband’s name of proprietor (s) and/or partners and Managing Director(s) in the case of Limited company

5. The date and current registration number of factory/ --------------------- shop/establishment/municipal Trade licence.

6. Nature of manufacturing activities at present. ---------------------

7. The type of weights and measures proposed to be --------------------- manufactured viz :

(i) Weights

(ii) Measures

(iii) Weighing Instruments

(iv) Measuring Instruments with details in each case.

8. The number of persons employed/proposed to be employed ---------------------

(i) Skilled

(ii) Semi-skilled

(iii) Unskilled

(iv) Specialist trained in the line

9. The monogram or trade mark intended to be imprinted --------------------- on weights and measures to be manufactured. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 13 13

10. Details of machinery, tools accessories, owned and used for manufacturing weights measures etc. ---------------------

11. Details of foundry/workshop facilities arranged, whether ownership, long term lease etc. ---------------------

12. Facilities of steel casting and hardness testing of vital parts etc or other means. ---------------------

13. Availability of electric energy. ---------------------

14. Details of loan received from Government or financial institution. If so, give details. ---------------------

15. Name of bankers, if any. ---------------------

16. VAT/Sales Tax Registration Number/CST Number/ professionalTax registration Number/IT Number. ---------------------

17. Have you applied previously for a manufacturer’s licence? If so, when and with what results? --------------------- 18

(a) Whether the item(s) proposed to be manufactured will be sold within the State or out side the state or both.

(b) Details of Model Approval received from Government of India;

(c ) When can you produce for inspection samples of your products for which licence is desired. -------- --------------------------------------------------------------------------------------------------------------------- To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rule, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. I/We agree to deposit the scheduled licence fee with Government as soon as required to do so by the Licencing Authority. All the information furnished above is true to the best of my/our knowledge. Place : ----------------------- Date : Signature and Designation mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 14 To be filled in by Departmental Officer of the State Government Date of Receipt of application : Serial Number of application : Date of inspection : Recommendation of Inspecting Officer : Place : -------------------------- Date : Signature and Designation of Inspecting Officer Final orders of Licensing Authority Licence granted/refused : Licence Number : Valid till : Place : ------------------------------ Date : Signature and Designation

SCHEDULE-II"A" [See rule 11(1)] Form LR-1 [Application for licence as repairers of Weights & Measures under the Legal Metrology Act, 2009] To, Sr. No. To be filled by Comments of the the applicants inspecting officer ------------------------------------------------------------------------------------------------------------------------ 1 2 3

1. Name of the concern seeking the licence. ---------------------

2. Complete address of the workshop. ---------------------

(a) Whether premises are owned/rented/taken, on lease dully supported by documents.

(b) Date of establishment. --------------------- ---------------------

4. Name (s) and address (s) along with their father’s/ mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 15 husband’s name of proprieter (s) and/or Partners and Managing Director (s) in the case of Limited company.

5. Number and date of shop/establishment/current Municipal Trade Licence. ---------------------

6. Professional Tax/IT Tax registration Number etc if any. ---------------------

7. The type of weights and measures proposed to be repaired viz:

8. Area in which you wish to operate. ---------------------

9. Previous experience in the line. ---------------------

10. Number of skilled staff empolyed or proposed to be empolyed ;

(i) skilled

(ii) semi skilled

(iii) unskilled

(iv) employees trained in the line

11. Details of machinery/tools/accessories available. ---------------------

12. Availability of electric energy. ---------------------

13. Have you sufficient stock of loan/test weights etc.? give details. ---------------------

14. Have you applied previously for a repairer’s licence? If so, when and with what results? --------------------- To be certified by the applicant(s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rule, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. I/We agree to deposit the Scheduled licence fees with Government as soon as required to do so by the Licensing Authority. All the information furnished above is true to the best of my/our knowledge. Place : -------------------------- Date : Signature and Designation mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 16 To be filled in by Departmental Officer of the State Government Date of Receipt of Application : Serial Number of application : Date of inspection : Recommendation of Inspecting Officer : Place : ------------------------------ Date : Signature and Designation of Inspecting officer Final orders of Licencing Authority Licence granted/refused : Licence Number : Valid till : Place : ------------------------------- Date : Signature and Designation

SCHEDULE-IIA [see rule 11(1)] Form LD-1 [ Application form for licence as dealers in Weights & Measures under the Legal Metrology Act, 2009] To, Sr No. To be filled by Comments of the the applicant inspecting officer 1 2 3

1. Name of the establishment/shop/person seeking the --------------------- licence.

2. Complete address of the establishment etc. ---------------------

3. Date of establishment. ---------------------

4. Name (s) and address (s) of proprietors and/or partners --------------------- and Managing Director (s) in the case of Limited company. --------------------- mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 17

5. Number and date of Registration Number of current --------------------- shop/establishment/Municipal Trade licence.

6. Categories of weights and measures sold/proposed --------------------- to be sold at present.

7. Registration Number of VAT/CST/Sales Tax/Professional --------------------- Tax/Income Tax.

8. Do you intend to import weights, etc. from places --------------------- outside the State/Country? If so indicate sources of supply. (Give details of manufacturer’s trade mark/ monogram and his licence number) and provide

(a) Registration of Importer of Weights and Measures, if any

(b) Approval of model imported into India by Central Government.

9. Have you applied previously for a dealer’s licence, --------------------- either in this State or elsewhere? If so give details ? To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rule, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. I/We agree to deposit the Scheduled licence fees with Government as soon as required to do so by the Licensing Authority. All the information furnished above is true to the best of my/our knowledge. Place : -------------------------- Date : Signature and Designation To be filled in by Departmental Officer of the State Government Date of Receipt of Application : Serial Number of application : Date of inspection : Recommendation of Inspecting Officer : Place : ------------------------------ Date : Signature and Designation of Inspecting officer mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 18 Sr No. 1 To be filled by the applicant 2 Comments of the inspecting officer 3

2. Name and complete address of the manufacturing concern for which renewal of licence is desired. Manufacturing Licence No --------------------- ---------------------

4. Name (s) and address (s) along with their father’s/ Husband’s name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company.

(a) Type of weight and measures which are --------------------- ---------------------

(b) Do you propose any change. The monogram or trade marks used on weights and ---------------------

6. Measures manufactured by you. Details of workshop facilities available. ---------------------

7. Details of production and sales in the last 5 years. ---------------------

8. Number and date of shop/establishment Registration Number. ---------------------

9. Registration Number of VAT/Sales Tax/CST/Professional Tax/Income Tax. --------------------- Final orders of Licencing Authority Licence granted/refused : Licence Number : Valid till : Place : ------------------------------ Date : Signature and Designation To,

SCHEDULE-IIB [see rule 11(2)] Form LM-2 [ Application for renewal of licence as manufacturer of Weights & Measures under the Legal Metrology Act, 2009] Manufactured as per licence granted. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 19 1 2 3

2. Name and complete address of the repairing concern seeking renewal of the licence. Repairer Licence Number. --------------------- ---------------------

4. Name (s) and address (s) along with their father’s/ Husband’s name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company. Registration Number and date of current shop/ --------------------- --------------------- establishment/Municipal Trade Licence.

5. Registration Number of VAT/Sales Tax/CST/Professional Tax/Income Tax. ---------------------

(a) The type of weights and measures repaired as per licence granted.

(b) Do you propose any change. --------------------- ---------------------

7. Area in which you are operating ---------------------

8. Have you sufficient stock of loan/test weights, etc. ---------------------

9. Please give details with particulars of stamping. --------------------- To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. I/We have deposited the Scheduled licence fees of Rs.-------------------(Rupees----------------- ----------) to the sub-Treasury/Bank on------------------------------------------and the original challan is enclosed. All the information furnished above is true to the best of my/our knowledge. Place : --------------------- Date : Signature and Designation

SCHEDULE-IIB [see rule 11(2)] Form LR-2 [ Application for renewal of licence as repairer of Weights & Measures under the Legal Metrology Act, 2009] To, Sr No. To be filled by Comments of the the applicant inspecting officer ------------------------------------------------------------------------------------------------------------------------ To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 20 I/We have deposited the Scheduled licence fees of Rs.-------------------(Rupees-------- ------------------------) to the sub-Treasury/Bank on------------------------------------------and the original challan is enclosed. All the information furnished above is true to the best of my/our knowledge. Place : --------------------- Date : Signature and Designation

SCHEDULE-IIB [see rule 11(2)] Form LD-2 [ Application for renewal of licence as dealer in Weights & Measures under the Legal Metrology Act, 2009] To, Sr.No. To be filled by the applicant 1 2 Comments of the inspecting officer 3

2. Name of the establishment/shop/person seeking the renewal of the licence. Dealer’s Licence Number. --------------------- ---------------------

3. Date of establishment. ---------------------

4. Name (s) and address (s) along with their father’s/ husband’s name of proprietor (s) and/or Partners and Managing Director (s) in the case of Limited company. ---------------------

5. Registration Number and date of shop/establishment/ current Municipal Trade Licence. ---------------------

6. Categories of weights and measures sold at present ---------------------

7. Registration Number of VAT/Sales Tax/CST/Professional Tax/Income Tax. ---------------------

8. Are you intending to import weights and measures etc. from places outside the State/Country? If so, indicate sources of supply from the State(s)/Country(s). (Give details of manufacturer’s trade mark/monogram and his licence number.) --------------------- To be certified by the applicant (s) Certified that I/We have read the Legal Metrology Act, 2009 and the Uttar Pradesh Legal Metrology (Enforcement) Rules, 2011 and agree to abide by the same and also the administrative orders and instructions issued or to be issued there under. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 21 I/We have deposited the Scheduled licence fees of Rs.-------------------(Rupees-------- ---------------) to the sub-Treasury/Bank on------------------------------------------and the original challan is enclosed. All the information furnished above is true to the best of my/our knowledge. Place : --------------------- Date : Signature and Designation

SCHEDULE-III [see rule 11(3)] Licensing Forms FORM LM-3 Government of Uttar Pradesh OFFICE OF THE CONTROLLER OF LEGAL METROLOGY Licence to manufacture, weights, measures, weighing or measuring instruments. Licence No……………………. Year……………… 1- The Controller of Legal metrology hereby grants to………………………………….. (Name and address of party or parties) a licence to manufacture the following:- (Include details of the weights, measures, weighing instruments or measuring instruments that are licenced to be manufactured by the party). 2- The licence is valid for the party named above in respect of his workshop located at……………………………………………………. 3- This licence is valid from…………………………to…………………………….. 4- The manufacturer shall comply with the conditions noted below. If he fails to comply with anyone of these, his licence is liable to be cancelled. 5- The trade mark monogram being used by the manufacturer is as under …………………… (Signature) Controller of legal Metrology Uttar Pradesh (Seal) Date ……………….. Place………………...

Note ; In the case of firm, its name with the names of all persons having interest in the business should be given in paragraph 1. CONDITIONS OF LICENCE

1. The person in whose favour this licence is issued shall.-

(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;

(b) Not encourage or countenance any infringement of the provisions of the Act. Or the Rules amended from time to time; mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 22

(d) Comply with any general or special directions that may be given by the Controller of Legal Metrology;

(e) Surrender the licence in the event of closure of business and/or cancellation of licence;

(f) present the weights, measures, weighing or measuring instruments as the case may be manufactured and meant for use within the State, to the legal metrology officers for verification and stamping before sale;

SCHEDULE-III [see rule 11(3)] Licensing Form FORM LR-3 Government of Uttar Pradesh OFFICE OF THE CONTROLLER OF LEGAL METROLOGY LICENCE TO REPAIR WEIGHTS,MEASURES, WEIGHING INSTRUMENTS OR MEASURING INSTRUMENTS Licence No…………… Year……………… 1- The Controller of Legal metrology hereby grants to……………………………………. (Name and address of party or parties) a licence to repair the following:- (Include details of the weights, measures, weighing instruments or measuring Instruments that are licenced to be repaired by the party). 2- The licence is valid for the party named above in respect of his workshop located at……………………………………………………. 3- This licence is valid from…………………………to…………………………….. 4- The repairer shall comply with the conditions noted below. If he fails to comply with anyone of these, his licence is liable to be cancelled. 5- The Party is licenced to repair weights, measures, weighing and measuring instruments in the areas mentioned below- …………….. (Signature) Controller of legal Metrology (Seal) Govt. of Uttar Pradesh Date ……………….. Place………………...

Note ; In the case of firm, its name with the name of all persons having interest in the business should be given in paragraph (1). CONDITIONS OF LICENCE

1. The person in whose favour this licence is issued shall.-

(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;

(b) Not encourage or countenance any infringement of the provisions of the Act. or the Rules for the time being in force;

(d) Comply with any general or special directions that may be given by the Controller of Legal Metrology;

(e) Surrender the licence in the event of closure of business and/or cancellation of licence; mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 24

(f) (i) Present the weights, measures, weighing or measuring instruments as the case may be duly repaired to the legal metrology officer for under taking verification and stamping as specified in rule 14, before delivery to the user.

(ii) In the case of weights measures weighing or measuring instruments, if they are serviced/repaired before the date on which the verification falls due and where, in the process and the verification stamp of the legal metrology officer is defaced, removed or broken, they shall be presented duly repaired to the legal metrology officer for reverification and stamping before delivery to the user.

(g) Submit the application for renewal of this licence as required under the rules within thirty days of expiry of the validity of the licence. 2- Every condition prescribed after the issue of this licence shall if notified in the Official Gazette, be binding on the persons to whom the licence has been granted.” Renewal entries Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date………… Renewed for Seal Controller of Legal Metrology mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 25 Schedule-III [see rule 11(3)] Licensing Forms Form LD-3 Government of Uttar Pradesh OFFICE OF THE CONTROLLER OF LEGAL METROLOGY Licence to a dealer in weights, measures, weighing instruments or measuring instruments . Licence No…………… Year……………… 1- The Controller of Legal metrology hereby grants to……………………………………. (Name and address of party or parties) a licence to deal in the following:- (Indicate details of the types weights and measures, weights, or measuring Instruments that are licenced to be dealt by the party). 2- The licence is valid for the party named above in respect of his premises located at……………………………………………………. 3- This licence is valid from…………………………to…………………………….. 4- The dealer shall comply with the conditions noted below. If he fails to comply with any one of those, his licence is liable to be cancelled. (Seal) Date ……………….. Place………………... ……………………… (Signature) Controller of legal Metrology Uttar Pradesh Note ; In the case of firm, its name with the names of all persons having any interest in the business should be given in paragraph (1). CONDITIONS OF LICENCE

1. The person in whose favour this licence is issued shall.-

(a) Comply with all the relevant provisions of the Act and Rules for the time being in force;

(b) Not encourage or countenance any infringement of the provisions of the Act. Or the Rules amended from time to time;

(d) Comply with any general or special directions that may be given by the Controller of Legal Metrology;

(e) Surrender the licence in the event of closure of business and/or cancellation of licence;

(f) submit the application for renewal of this licence as required under the rules within thirty days of expiry of the validity of the licence.

(g) Not sell or offer, expose or possess for sale any non-standard weight or measure. mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 26 2- Every condition prescribed after the issue of this licence shall if notified in the Official Gazette, be binding on the persons to whom the licence has been granted. Renewal entries Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date…………… Renewed for Seal Controller of Legal Metrology Current no…………………….Date………… Renewed for Seal Controller of Legal Metrology

SCHEDULE-IV [See rule – 11(4) & (5)] Government of Uttar Pradesh Office of Controller of Legal Metrology Licencing and renewal fees for manufacturers, repairers or dealers of weights and measures

1. Issue of licence/renewal of licence to:

(i) Manufacturers Rs. 500/- per year

(ii) Repairers Rs. 100/- per year

(iii) Dealers Rs 100/- per year

2. Alteration of licence : Rs. 50/-

3. Issue of duplicate licence : Rs. 10/- mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 27

SCHEDULE-V [See rule 11 (6)] Government of Uttar Pradesh Office of Controller of Legal Metrology Register of licenced Manufacturers/Repairers/Dealers of weights, measures, weighing/measuring instruments Office of………………………………. Lice nce num ber Date of issue/ renew al Name and complete address of the manufacturer/ repairer/ dealer Place where workshop/ factory is situated Articles to be manufactured/ repaired/sold Trade mark/ monogram being used Orders regarding cancellation of licence Result of appeal Signature of competent authority remark 1 2 3 4 5 6 7 8 9 10 Note : Column (4) does not apply to dealers, column (6) does not apply to repairers and dealers.

SCHEDULE – VI [See rule 11(8)] Government ofUttar Pradesh Office of Controller of Legal Metrology Security deposit to be made by licenced repairer Repairer of weights and measures including weighing Rs. 200-00 and measuring instruments.

SCHEDULE – VII [See rule 13] FormLM-4 Register to be maintained by the manufacturers of weights and measures. 1- Name and address of the manufacturer………………………………………………………. 2- Description of the weight or measure………………………………………………………… 3- (i) No. of the manufacturing licence………………………………………………………

(ii) Date on which the licence was issued……………………………………………………

(iii) Period of validity of the licence………………………………………………………… 4- Particulars of order, if any,suspending or revoking………………………………………………. the licence. S.No. Month Unsold stock from previous month Quantity manufactured during the month Total 3+4 Sold within the state No. of item sold Dispatch voucher no. and date 1 2 3 4 5 6 7 sold outside the state Dispatch voucher no. and date Total sold (6+9) Balance (5-11) Remarks Name of the State No. of items sold 8 9 10 11 12 13 mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 28 Schedule – VII [See rule 13] FORM LR-4 Register to be maintained by the repairer in respect of weights, measures Name and address of the repairer…………………………. ………… License No.……………. Date of Licensing……………………… S.No. Date Name of the user from whom received Items and their Nos. booked for repair Receipt No. and date of issue to the user 1 2 3 4 5 Amount of repairing charges Amount of verification fee Total amount charged Dated of return to the user Remarks 6 7 8 9 10 Schedule – VII [ See rule 13 ] LD-4 Register to be maintained by dealer in weights and measures. 1- Name and address of the dealer…………………………………………………………….. 2- Description of the weight or measure………………………………………………………. 3- (i) Dealer licence No………………………………………………………………………...

(ii) Date on which the licence was issued…………………………………………………...

(iii) Period of validity of licence……………………………………………………………. 4- Particulars of order, if any suspending or…………………………………………………… Revoking the licence. 5- Category of weight or measure……………………………………………………………… (Category A or B ) Sr. No. Month Unsold stock from the previous month Brought from within the State during the month Brought from outside the state during the month Total (3+4+5) 1 2 3 4 5 6 mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 29 Quantity Denomination Weighing instruments Measuri -ng instruments Verificati on fee Rs. P. Carriage, conveyance adjusting charges etc. weights measures Capacity class Manufa -cturer Type 1 2 3 4 5 6 7 8 9 10 Sold within the State Sold outside the state Total sold ( 7+9) Balance (6-12) Remarks No. of items sold Dispatch voucher no. and date No. of items sold Dispatch voucher no. and date Name of the state 7 8 9 10 11 12 13 14 Schedule- VIII [See rule 16 (3)] Government of Uttar Pradesh Office of the Controller, legal metrology, Certificate of verification Name of Legal Metrology officer………………………………………………………………….. No……………………… I hereby certify that I have this day verified and stamped/rejected the under mentioned weights, measures, etc. Belonging to………………………………………….Locality……………………………………… Total Rs…………………..deposited vide T. Receipt/Money receipt No………..dated…………… Repaired by/used by ………………………(Signature) Next verification due on…………………… Legal Metrology officer Note:- In the case of rejected weights, measures, etc the legal metrology officer shall give separate Certificate of rejection mentioning the reasons of rejection against each item. Schedule-IX [See Rule 17(1)] Fee payable for verification and stamping of Weights and Measures and Weighing and Measuring Instruments 1- (a) Bullion Weights: Denomination

(1) Fee per piece (Rs.)

(2) 10kg 30.00 5kg 20.00 2kg 20.00 1kg 20.00 500g 15.00 200g 15.00 100g 15.00 mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 30 Denomination

(1) Fee per Piece (Rs.)

(2) 500mg 5.00 200mg 5.00 100mg 5.00 50mg 5.00 50g 15.00 20g 15.00 10g 15.00 5g 15.00 2g 15.00 1g 15.00

(b) Carat Weight: 100g (500 c) 20.00 40g (200 c) 20.00 20g (100 c) 20.00 10g (50 c) 20.00 4g (20 c) 20.00 2g (10 c) 20.00 1g (5 c) 20.00 400mg (2 c) 20.00 200mg (1 c) 20.00 100mg (0.5 c) 20.00 40mg (0.2 c) 20.00 20mg (0.1 c) 20.00 10mg (0.05 c) 20.00 4mg (0.02 c) 20.00 2mg (0.01 c) 20.00 1mg(0.005 c) 20.00

(1) Fee per piece (Rs.)

(2) 10kg 20.00 5kg 20.00 2kg 15.00 1kg 10.00 500g 5.00 200g 5.00 100g 5.00 50g 5.00 20g 5.00 10g 5.00 5g 5.00 2g 5.00 1g 5.00

(d) Sheet metal Weight (other than Bullion) mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 31 Denomination

(1) Fee per piece (Rs.)

(2) 100 litre and above Rs. 50 for the Ist 100 litre plus Rs. 7 for every additional 100 litre or part thereof subject to maximum Rs. 5000. 50 l 50.00 20 l 20.00 10 l 20.00 5 l 10.00 2 l 10.00 1 l 10.00 20mg 5.00 10mg 5.00 4mg 5.00 5mg 5.00 2mg 5-00 1mg 5.00

(e) Iron hexagonal, knob type weights and parallelepiped weights: Denomination

(1) Fee per piece (Rs.)

(2) 50Kg 25.00 20Kg 20.00 10kg 20.00 5kg 20.00 2kg 15.00 1kg 10.00 500g 5.00 200g 5.00 100g 5.00 50g 5.00 20g 5.00 10g 5.00 5g 5.00 2g 5.00 1g 5.00

(f) Standard weights for testing for high capacity weighing machines : Denominations Fee corresponding to Max permissible relative error

0.5/10000 in Rs. Fee corresponding to Max permissible relative error

3.3/10000, 1.7/10000 and

1.0/10000 in Rs. 100kg 75.00 50.00 200kg 150.00 100.00 500kg 300.00 200.00 1000kg 750.00 500.00 2000kg 1500.00 1000.00 5000kg 3000.00 2000.00 2- Capacity Measures : mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 32 Denomination

(1) Fee per piece (Rs.)

(2) 2 m. 10.00 1 m. 10.00

0.5 m 20.00 1 m. graduated (at every cm) 20.00

0.5 m. graduated (at every cm) 20.00 Denomination

(1) Fee per piece (Rs.)

(2) 200kg 400.00 100kg 300.00 50Kg 150.00 20Kg 150.00 10kg 150.00 500 ml 10.00 200 ml 10.00 100 ml 10.00 50 ml 10.00 20 ml 10.00 10 ml 10.00 5 ml 10.00 2 ml 10.00 1 ml 10.00 3- Length Measures:

(a) Non- Flexible –

(b) Fabric Plastic/Woven/Steel tapes- Accuracy Class

(1) Fee per metre in Rs.

(2) Class-1 1.00 Class-II 1.00 Class-III 0.50

(1) Fee per piece (Rs.)

(2) 1 m. 10.00

0.5 m. 10.00

(d) Surveying Chain- Denomination

(1) Fee per piece (Rs.)

(2) 30 m. 100.00 20 m. 100.00 4- Beam Scale Class A & B : mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 33 400t 4000.00 300t 3000.00 200t 3000.00 150t 2000.00 100t 2000.00 80t 2000.00 60t 2000.00 50t 2000.00 40t 2000.00 30t 2000.00 25t 2000.00 20t 2000.00 15t 2000.00 10t 1000.00 5t 500.00 3t 400.00 2t 400.00 1500kg 300.00 1000kg 300.00 500kg 300.00 300kg 200.00 250kg 200.00 200kg 100.00 150kg 100.00 100kg 100.00 50kg 100.00 30kg 100.00 5kg 100.00 2kg 100.00 1kg 100.00 500g and below 60.00 5- Beam Scales Class C& D: Denomination

(1) Fee per piece (Rs.)

(2) 1000kg 200.00 500kg 200.00 300kg 200.00 200kg 100.00 100kg 100.00 50Kg 20.00 20Kg 20.00 10kg 20.00 5kg 15.00 2kg 15.00 1kg 15.00 500g and below 10.00 6- Non-Automatic weighing instruments – Mechanical (analogue) Class III & IV : mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 34 400t 4000.00 300t 3000.00 200t 3000.00 150t 2000.00 100t 2000.00 80t 2000.00 60t 2000.00 50t 2000.00 40t 2000.00 30t 2000.00 25t 2000.00 20t 2000.00 15t 2000.00 10t 1000.00 5t 1000.00 3t 500.00 2t 500.00 1500kg 250.00 1000kg 250.00 500kg 250.00 300kg 200.00 250kg 200.00 200kg 200.00 150kg 200.00 100kg 200.00 50kg 200.00 30kg 200.00 25kg 200.00 20kg 100.00 15kg 100.00 10kg 100.00 5kg 100.00 3kg 100.00 2kg 100.00 1kg 100.00 500g. and below 100.00 25kg 60.00 20kg 60.00 15kg 30.00 10kg 30.00 5kg 30.00 3kg 30.00 2kg 30.00 1kg 15.00 500g. and below 15.00 7- Non-Automatic Weighing Instruments – Electronic Class III & IIII mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 35 8- Non-Automatic Weighing instruments both mechanical and electronics class I & II Capacity Fee (Rs.) Exceeding 50 t 3000.00 Not exceed 50 t but exceed 10t 2000.00 Not exceed 10t but exceed 1t 1000.00 Not exceed 1t but exceed 50kg 500.00 Not exceed 50kg but exceed 10kg 250.00 Not exceed 10kg 200.00 9- Automatic Weighing Instrument: Capacity Fee in Rs. Exceeding 100t T

4000.00 Not exceeding 100t but exceeding 50t 3000.00 Not exceeding 50t but exceeding 10t 2000.00 Not exceeding 10t but exceeding 1t 1000.00 Not exceeding 1t but exceeding 50kg 500.00 Not exceeding 50kg but exceeding 10kg 250.00 Not exceed 10kg 200.00 10- Volumetric measuring instruments:

(a) Dispensing pumps each pump : Rs. 1000.00 per unit

(b) Totalizing counter : Rs. 500.00 per unit

(c) Other instruments : Capacity Fee in Rs. Exceeding 100litre Rs. 500.00 for the 1st 100 liters plus Rs. 250 for every additional 100 liters or part thereof Not exceeding 100litre but exceeding 50litre 500.00 Not exceeding 50 litre but exceeding 20litre 250.00 Not exceed 20litre 200.00 11- Flow Meters: Flow rate up to 100litre/min. Rs. 2000.00 Above 100 litre/min upto 500litre/min. Rs. 3000.00 Above 500litre/min. Rs. 5000.00 12- Linear Measuring Instruments: Taxi, Autorishaw meters Rs. 100.00 Other meters Rs. 50 for the Ist 1000m. or part there of Plus Rs. 5.00 for every additional 100m. or part thereof 13- Clinical Thermometer Rs. 0.50 per unit 14- Water meter Rs. 25.00per unit mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 36 16- C.N.G. Dispenser Rs. 1000.00 per unit 17- L.P.G. Dispenser Rs. 1000.00 per unit 18- Counter Machine 15- Peg Measure: 30ml 50.00 60ml 50.00 100ml 50.00 up to 10kg Rs. 20.00 per unit above 10kg Rs. 50.00 per unit

SCHEDULE –X [See rule 26(1)] Form of appeal against an order of a Legal Metrology Officer/Controller Legal Metrology :- 1- Name and address of the appeallant 2- No. and date of order of Legal Metrology officer/Controller of Legal Metrology against which the appeal is preferred. 3- Whether the appellant desires to be heard in person or through an authorized representative. 4- Grounds of appeal

SCHEDULE-XI [See rule 27] Compounding fees for various offences Sr.No. Section and nature of offence Penal Section Compounding fee 1 S. 8(3) Use of weight, measure of numeration other than the Standard weight, measure or numeration 25 Minimum Rs. 2000=00 which may extend to Rs. 25000=00 2 S. 8(4) Manufacture of weight or measure not conforming to Standards 27 Minimum Rs. 2000=00 which may extend to Rs. 20000=00 3 S. 10 Transaction or dealing or contract in respect of goods etc, by weight, measure or number other than prescribed. 28 Minimum Rs. 2000=00 which may extend to Rs. 10000=00 4 S. 11 Quote or make announcement or issue or exhibit of price list or changing of price other than in accordance with standard unit of weight or measure or numeration. 29 Minimum Rs. 2000=00 which may extend to Rs. 10000=00 5 S. 12 Demanding or receiving any articles or thing or service in excess or less than the quantity specified by contract or agreement. 30 Minimum Rs. 2000=00 which may extend to Rs. 10000=00 6 S. 17 Maintenance of records, registers by manufacturer, dealer or repairer and non production of weight, measure document or register on demand 31 Minimum Rs. 2000=00 which may extend to Rs. 5000=00 7 S. 18(1) Non Compliance of declaration in 36(1) For 1st offence mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 37 respect of pre-packaged commodity by manufacturer/dealer Minimum Rs. 2000=00 which may extend to Rs. 25000=00 for 2nd offence minimum Rs. 25000=00 which may extend to Rs. 50000=00 For the subsequent offence minimum Rs. 50000=00 which may extend to Rs. 100000=00 8 S. 18(1) Non Compliance of net quantity requirement of pre-packaged commodity by manufacturer 36(2) For 1st offence Minimum Rs. 10000=00 which may extend to Rs. 50000=00 for 2nd or subsequent offence minimum Rs. 50000=00 which may extend to Rs. 100000=00 9 S. 23 Manufacture of weight or measure without licence 45 Minimum Rs. 5000=00 which may extend to Rs. 20000=00 10 S. 23 Repair/sale of weight or measure without licence 46 Minimum Rs. 2000=00 which may extend to Rs. 5000=00 11 S. 24 Use of unverified weight or measure in transaction or protection 33 Minimum Rs. 2000=00 which may extend to Rs. 10000=00 12 S. 33 sale of unverified weight or measure 33 Minimum Rs. 2000=00 which may extend to Rs. 10000=00 13 S. 34 Sale or delivery of commodities by nonstandards weights or measure 34 Minimum Rs. 2000=00 which may extend to Rs. 5000=00 14 S. 35 Rendering service by non-standard weight or measure 35 Minimum Rs. 2000=00 which may extend to Rs. 5000=00 mÙkj izns'k vlk/kkj.k xtV] 1 vizSy] 2011 38 15 S. 47 Tampering with licence 47 Minimum Rs. 5000=00 which may extend to Rs. 20000=00 16 S. 53(3) Violation of any rule made under the Act 53(3) Minimum Rs. 500=00 which may extend to Rs. 5000=00 By order’ NET RAM, Pramukh Sachiv

Uttar Pradesh Legal Metrology(Enforcement) Rules 2011

The enactment

Full text

Find the provision, not just read it